Yaskawa P7 Drive User Manual - Manual (Page 208)

Capacity Related Parameters B - 4
Capacity Related Parameter Values
The following tables detail the factory default settings for the parameters that are affected by the setting of parameter o2-04.
Table B.3 208/240VAC Drives
Drive Model
CIMR-_ _ _
Nominal
Hp
Factory
Default
for
b8-04
Factory
Default
for
C6-02
Factory
Default
for
E2-01
Factory
Default
for
E2-03
Factory
Default
for
E2-05
Factory
Default
for
L2-02
Factory
Default
for
L2-03
Factory
Default
for
L2-04
Factory
Default
for
L8-02
Factory
Default
for
L8-06
20P4 0.5/0.75 288.2 10kHz 1.9 1.2 9.842 0.1 0.1 0.3 95 ° C 5
20P7 2 223.7 10kHz 3.3 1.8 5.156 0.1 0.2 0.3 95 ° C 7.5
21P5 1.5/2 169.4 10kHz 6.2 2.8 1.997 0.2 0.3 0.3 95 ° C 10
22P2 3 156.8 8kHz 8.5 3.0 1.601 0.3 0.4 0.3 100 ° C 12
23P7 5 122.9 10kHz 14.0 4.5 0.771 0.5 0.5 0.3 95 ° C 12
25P5 7.5 94.75 15kHz 19.6 5.1 0.399 1.0 0.6 0.3 95 ° C 10
27P5 10 72.69 15kHz 26.6 8.0 0.288 1.0 0.7 0.3 95 ° C 17
2011 15 70.44 8kHz 39.7 11.2 0.230 1.0 0.8 0.3 95 ° C 21
2015 20 63.13 10kHz 53.0 15.2 0.138 2.0 0.9 0.3 90 ° C 17
2018 25 57.87 10kHz 65.8 15.7 0.101 2.0 1.0 0.6 100 ° C 15
2022 30 51.79 10kHz 77.2 18.5 0.079 2.0 1.0 0.6 90 ° C 24
2030 40 46.27 10kHz 105.0 21.9 0.064 2.0 1.1 0.6 90 ° C 20
2037 50 38.16 5kHz 131.0 38.2 0.039 2.0 1.1 0.6 95 ° C 18
2045 60 35.78 5kHz 160.0 44.0 0.030 2.0 1.2 0.6 100 ° C 20
2055 75 31.35 8kHz 190.0 45.6 0.022 2.0 1.2 0.1 105 ° C 17
2075 75/100 23.10 2kHz 260.0 72.0 0.023 2.0 1.3 0.1 110 ° C 16
2090 125 20.65 2kHz 260.0 72.0 0.023 2.0 1.5 0.1 100 ° C 18
2110 150 18.12 2kHz 260.0 72.0 0.023 2.0 1.7 0.1 95 ° C 20
Note: b8-04 = Energy Savings Coefficient
C6-02 = Carrier Frequency
E2-01 = Motor Rated Current
E2-03 = Motor No-Load Current
E2-05 = Motor Line-to-Line Resistance
L2-02 = Momentary Power Loss Ride-Thru Time
L2-03 = Momentary Power Loss Minimum Base Block Time
L2-04 = Momentary Power Loss Voltage Recovery Ramp Time
L8-02 = Overheat Pre-Alarm Level
L8-06 = Input Phase Loss Detection Level