Yaskawa P7 Drive User Manual - Manual (Page 241)

Index - 1
A
A. TUNE.................................................................. 3-6, 3-13
AC Reactor ....................................................................... E-6
Accel/Decel
Parameters .................................................................A-8
Switch Frequency ......................................................A-8
Time ........................................................................ 5-25
Acceleration
Stall Prevention Level during .............. 5-40, 6-16, A-19
Time................................................................ 5-25, A-8
Troubleshooting.......................................6-7, 6-10, 6-16
Access Level ........................................................... 5-2, A-2
ADV ........................................................................ 3-6, 3-12
Alarm Displays & Processing........................................... 6-8
ALARM Indicator ............................................................ 3-4
Altitude .............................................................................C-4
Ambient Temperature .................................... 1-13, 6-17, C-4
Analog Inputs
Bias ....................................................... 5-33, 5-38, A-16
Connection Diagram................................................ 2-27
Control Circuit Terminals........................................ 2-23
Gain ...................................................... 5-33, 5-38, A-16
Parameters ...............................................................A-16
Troubleshooting....................................................... 6-14
Analog Outputs
Bias ......................................................................... A-17
Connection Diagram................................................ 2-27
Control Circuit Terminals........................................ 2-23
Gain .........................................................................A-17
Parameters ...............................................................A-17
ASIC Faults ...................................................................... 6-3
Auto Restart.................................................................... 5-44
Count Reset ............................................................. 5-44
Faults Covered......................................................... 5-44
Max. Restart Time After Fault ................................ 5-44
Number of Attempts ................................................ 5-44
Auto-Tuning
Fault Displays and Processing................................. 6-12
How to ..................................................................... 5-59
Line-to-Line Resistance ..........................................A-11
Menu................................................................. 3-6, 3-13
Motor Rated Current ............................. 4-6, A-11, A-24
Motor Rated Power .................................................A-24
B
Base Block
After Fault ..................................................... 5-44, A-19
Circuit Fault............................................................... 6-2
Minimum Time ....................................... 5-7, A-19, B-4
Basic Programming...............................................5-1 to 5-60
Baud Rate .........................................................6-8, D-2, D-4
Bias Adjustments .............................. 5-33, 5-38, A-16, A-17
Braking
DC Injection............................................................... 5-9
High-Slip................................................................. A-22
Dynamic................................................................... 2-12
Branch Short Circuit Protection................................E-2, E-3
Broken Belt (Undertorque detection).............................. 5-46
C
Cable Length ................................................................... 2-11
Capacitors ......................................................................... 7-2
Capacity, Rated Output ........................................... C-2, C-3
Capacity Related Parameters .......................................... B-1
Carrier Frequency
Error ......................................................................... 6-11
Lower Limit ............................................................. A-9
Parameters................................................................. A-9
Proportional Gain ..................................................... A-9
Selection ................................................................... A-9
Upper limit ............................................................... A-9
Vs. Cable Length ..................................................... 2-11
Characteristic Frequency ................................................ 6-18
Charge Indicator (LED) ............................. 1-6, 2-2, 4-5, C-4
Circuit Breakers .................................................2-9, E-2, E-3
Clearances ....................................................................... 1-14
Coast to Stop .................................................. 5-6, 5-32, 5-48
Coast w/Timer................................................................. 5-32
Com OPT Setup Parameters........................................... A-11
Communications Modbus/Serial..............A-18, D-1 to D-14
Errors (CPF)............................................. 6-2 to 6-4, 6-8
Parameters............................................................... A-18
Component Names.....................................................1-5, 1-6
Connections
Preventive Maintenance............................................. 7-3
Connectors
Inspection................................................................... 7-2
Sizing ...............................................................2-3 to 2-7
Contactors
Magnetic ...................................................................E-6
Soft Charge ............................................................. 6-21
Control Circuit
Characteristics......................................... 6-7, 6-10, 6-21
Control Circuit (Continued)
Connection Diagram......................................... 2-27
Analog Input Terminal Configuration ............. 2-21
PCB
Inspecting ........................................................... 7-2
Power Fuse............................................................... 6-22