Yaskawa P7 Drive User Manual - Manual (Page 244)

Index - 4
H
Hand
Frequency Reference Selection..................................5-4
Hardware Protection Parameters ...........................5-48, A-21
Harmonics, Power Supply ....................................... C-2, C-3
Heat Loss Data ................................................................1-11
Heatsink Time ...................................................................7-4
Heatsink Fan............................................................ 5-49, 7-4
High-Slip Braking .......................................................... A-22
Horsepower, converting to kW........................................5-59
Humidity..........................................................................1-13
Ambient Operating.................................................... C-4
Hunting Prevention
Parameters ...............................................................A-21
Troubleshooting .......................................................6-18
I
IEC IP00 ............................................................................1-4
IEC IP20 ............................................................................1-4
IGBT (Transistor Module)
Testing ..................................................................... 6-22
INCREASE Key...................................................... 3-3, 5-54
Troubleshooting .......................................................6-14
Indicators, Mode................................................. 3-2, 3-4, 3-5
Initialization .....................................................................5-1
Mode Selection...........................................................5-2
Parameters .................................................................A-2
Specification Selection............................................A-24
User .................................................................. 5-3, 5-54
Input
Diodes, Inspecting......................................................7-2
Fuses .......................................................... 2-9, E-2, E-3
Multi-function Terminals
Analog Inputs..............2-23, 2-27, 5-33, 5-38, A-16
Digital Inputs ................................ 2-23, 2-27, A-12
Phase Loss Detection Level ......................6-6, A-21
Terminal Status (U1-10) .........................................A-25
Voltage ....................................................A-10, C-2, C-3
Setting ............................................. 4-5, 5-22, A-10
Inputs
Analog Inputs ....................................... 2-23, 2-27, A-16
Digital Inputs........................................ 2-23, 2-27, A-12
Inspection
Periodic ......................................................................7-2
Receiving....................................................................1-3
Installation
Electrical ...................................................................2-1
Physical .....................................................................1-1
Adverse Conditions...........................................1-13
Orientation & Clearances ................................. 1-14
Site............................................................ 1-13, C-4
Integral Control (PI)........................................................ 5-16
IPM (Intelligent Power Module)
Inspecting................................................................... 7-2
J
Jog Frequency Reference ....................................... 2-23, A-9
Jump Frequency ...................................................... 5-27, A-9
Troubleshooting ....................................................... 6-19
K
Keypad ............................................................................. 3-2
kVA, Auto-Tuning .......................................................... 5-59
kW, Converting from HP ................................................ 5-59
kWH User Monitor Initialization................................... A-24
L
Lamps, Indicator .................................................3-2, 3-4, 3-5
Language Selection................................................... 5-2, A-2
LCD Display ..................................................................... 3-2
Lights .................................................................3-2, 3-4, 3-5
Line-to-Line Resistance, Motor ......................................A-11
LOCAL
Frequency Reference Selection ......................... 3-3, A-4
Indicators ............................................................ 3-4, 3-5
Key...................................................................... 3-2, 3-3
Function Selection ........................................... A-24
Mode .......................................................................... 3-4
Troubleshooting ....................................................... 6-15
LonWorks...................................................................5-4, 5-5
Loss of Load ................................................................... 5-46
M
Main Circuit
Terminals ....................................................2-2, 2-3, 2-8
Test Procedure ......................................................... 6-20
Wire Sizes and Connectors ..............................2-3 to 2-7
Wiring Diagrams ..................................2-9 to 2-11, 2-27
Main Menu
Functions ................................................................... 3-6
Structure..................................................................... 3-7
Maintenance............................................................7-1 to 7-6
Mass, Drive (Weight)............................................1-7 to 1-10
Master Frequency Reference Terminal Selection . 5-39, A-16
Mechanical Vibration ..................................................... 6-18