Alcatel Carrier Internetworking Solutions Omni Switch/Router - Manual (Page 953)

Modifying a PPP Entity
Page 30-15
Modifying a PPP Entity
The pppmodify command is used to modify the parameters of an existing PPP Entity. To
modify a specific PPP Entity, for example Peer ID 1, enter the following command:
pppmodify p1
A screen similar to the following displays:
Modify PPP for communication to Peer ID: 1
Enter PPP parameters:
1)
Description :
{Enter text up to 30 characters}
2) Administrative Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enabled
{(E)nable, (D)isable}
3) PPP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Normal
{(N)ormal, (M)ultilink}
4) Compression Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . None
{(N)one, STAC-(L)ZS}
5) Bridging Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
{1-65535 or 0 if no Bridging}
50) Bridge Config Admin Status . . . . . . . . . . . . . . . . . . . . . Enabled
{(E)nabled, (D)isabled}
51) PPP Bridging Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet Only
{Bridge (A)ll, (E)thernet Only}
6) Routing Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
{1-65535 or 0 if no Routing}
60) IP Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . . Enabled
{(E)nabled, (D)isabled}
61) Remote IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0.0.0
{IP address or 0.0.0.0 = learn, if IP enabled}
62) IPX Config Admin Status . . . . . . . . . . . . . . . . . . . . . . . . Disabled
{(E)nable, (D)isable}
7) Authentication Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAP
{(N)one, (P)AP, (C)HAP}
70) User ID received from remote for Authentication . . .
{0 (No ID) to 8 ASCII characters}
71) Password received from remote for Authentication .
{0 (No Password) to 8 ASCII characters}
72) User ID sent to remote for Authentication . . . . . . . . .
{0 (No ID) to 8 ASCII characters}
73) Password sent to remote for Authentication . . . . . . .
{0 (No Password) to 8 ASCII characters}
8) Max Failure Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
{1..65535}
9) Max Configure Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
{1..65535}
10) Max Terminate Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
{1..65535}
11) Retry Timeout Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
{Retry Timeout in Second(s) 1..65535}
12) Fragmentation Interleaving . . . . . . . . . . . . . . . . . . . . . . . . . No
{Fragmentation Interleaving Yes or No
121) Fragmentation Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 0
{Fragmentation Delay in milliseconds(ms)}
122) Limit Maximum number of fragmentation to 16 . . . . . No
{(Y) meant cisco compatible. (N) meant native}
:
The fields on this screen are the same as those produced by the pppadd command. See
Adding a PPP Entity on page 30-9 for descriptions of each of these fields.
Make the desired changes to any of the parameters, then enter the save command to
implement the changes. You will then be returned to the system prompt.