Viewing an isdn configuration entry, Viewing an isdn configuration entry -6 – Alcatel Carrier Internetworking Solutions Omni Switch/Router User Manual
Page 984
Viewing an ISDN Configuration Entry
Page 32-6
Viewing an ISDN Configuration Entry
The
isdnv
command is used to view the configuration of existing ISDN configuration entries.
You can either view a configuration summary for all ISDN ports on a specified slot, or display
the configuration for a single ISDN port.
To view configuration information on all ISDN ports on a specific slot, for example, slot 4,
enter the following command:
isdnv 4
A screen similar to the following displays:
View ISDN Configuration for Slot: 4, Port: 2.
1)
Switch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ETSI
2)
B1 Signalling Calling Address. . . . . . . . . . . . . . . . . . . . . . . .
3)
B1 Service Profile Identifier (SPID) . . . . . . . . . . . . . . . . . . .
4)
B2 Signalling Calling Address. . . . . . . . . . . . . . . . . . . . . . . .
5)
B2 Service Profile Identifier (SPID) . . . . . . . . . . . . . . . . . . .
View ISDN Configuration for Slot: 4, Port: 4.
1)
Switch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ETSI
2)
B1 Signalling Calling Address. . . . . . . . . . . . . . . . . . . . . . . .
3)
B1 Service Profile Identifier (SPID) . . . . . . . . . . . . . . . . . . .
4)
B2 Signalling Calling Address. . . . . . . . . . . . . . . . . . . . . . . .
5)
B2 Service Profile Identifier (SPID) . . . . . . . . . . . . . . . . . . .
To view information on a specific ISDN port and slot, for example, slot 4, port 4, enter the
following command:
isdnv 4/4
A screen similar to the following displays:
View ISDN Configuration for Slot: 4, Port: 4.
1)
Switch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ETSI
2)
B1 Signalling Calling Address. . . . . . . . . . . . . . . . . . . . . . . .
3)
B1 Service Profile Identifier (SPID) . . . . . . . . . . . . . . . . . . .
4)
B2 Signalling Calling Address. . . . . . . . . . . . . . . . . . . . . . . .
5)
B2 Service Profile Identifier (SPID) . . . . . . . . . . . . . . . . . . .
The fields on this screen are the same as those produced by the
isdnm
command:
Switch Type
Specifies the type of switch to which this ISDN port is to be connected. The options are:
AT&T 5ESS (
5ESS
), Northern Telecom DMS100 (
DMS100
), National ISDN-1 Bellcore (
NI1
), and
Euro-ISDN ETS 300/British Telecom NET3 (
ETSI
).
B1/B2 Signalling Calling Address
The number assigned to this channel by the carrier. If only one address is supplied by the
carrier, it should be assigned to channel B1, and channel B2 should be left empty.
B1/B2 Service Profile Identifier (SPID)
The Service Profile Identifier assigned to this channel by the carrier. Normally, this value
contains the calling address surrounded by some digits. If only one address is supplied by the
carrier, it should be assigned to channel B1, and channel B2 should be left empty.