Lenze EVF9383 - Manual (Page 154)

Configuration
2−146
l
EDSVF9383V−EXT EN 2.0
+
-
C 1 3 3 4
C 1 3 3 5
P C T R L 2 - S E T
C 1 3 3 0
C 1 3 3 1
P C T R L 2 - O U T
C 1 3 4 0 / 2
P C T R L 2
± 1 0 0 %
R E S E T
C 1 3 4 1 / 1
P C T R L 2 - R F G - L O A D
C 1 3 4 5 / 1
C 1 3 4 0 / 1
P C T R L 2 - R F G - S E T
C 1 3 4 4 / 1
C 1 3 4 4 / 2
C 1 3 3 2
C 1 3 3 3
C 1 3 3 6
C 1 3 3 7
P C T R L 2 - A C T
C 1 3 4 0 / 3
C 1 3 4 4 / 3
C 1 3 4 1 / 2
P C T R L 2 - I - O F F
C 1 3 4 5 / 2
C 1 3 4 1 / 3
P C T R L 2 - I N A C T
C 1 3 4 5 / 3
P C T R L 2 - I N F L
C 1 3 4 0 / 4
C 1 3 4 4 / 4
C 1 3 4 1 / 4
P C T R L 2 - O V E R L A Y
C 1 3 4 5 / 4
R F G = 0
Fig. 2−122 Process controller (PCTRL2)
Signal Source Note
Name Type DIS DIS format CFG List Lenze
PCTRL2−RFG−SET a C1344/1 dec [%] C1340/1 1 1000 The process setpoint is shown at
PCTRL2−SET with any start value via a
ramp generator.
The function is activated using
PCTRL−RFG−LOAD.
PCTRL2−RFG−LOAD d C1345/1 bin C1341/1 2 1000 HIGH = Function of PCTRL2−RFG−SET is
active
PCTRL2−SET a C1344/2 dec [%] C1340/2 1 1000 Input for process setpoint. Possible value
range: ±200 %. The time of step−change
signals can be decelerated via the ramp
generator (C1330 for the acceleration time;
C1331 for the deceleration time).
PCTRL2−ACT a C1344/3 dec [%] C1340/3 1 1000 Input for actual value; value range ±200 %
PCTRL2−INFL a C1344/4 dec [%] C1340/4 1 1000 Evaluation (influence) of the output signal;
value range ±200 %
PCTRL2−I−OFF d C1345/2 bin C1341/2 2 1000 HIGH = switch off I component (online)
LOW = switch off I component (online)
PCTRL2−INACT d C1345/3 bin C1341/3 2 1000 HIGH = Inactivation of the process
controller (online)
PCTRL2−OVERLAY d C1345/4 bin C1341/4 2 1000 HIGH = Show influence
LOW = Hide influence
PCTRL2−OUT a − − − − − −
Range of functions
l Control characteristic
l Ramp generator
l Value range of the output signal
l Evaluating the output signal
l Deactivating the process controller