Lenze EVF9383 - Manual (Page 231)

Appendix
Index
5−5
l
EDSVF9383V−EXT EN 2.0
− Blocking frequencies (NLIM), 2−132
− building up a connection, 2−37
− Change−over (ASW), 2−61
− Characteristic function (CURVE), 2−77
− Code assignment (FEVAN), 2−101
− Comparison (CMP), 2−69
− configuration code, 2−34
− connecting, 2−35
− Conversion (CONV), 2−74
− Conversion phase to analog (CONVPHA), 2−76
− Counter (FCNT), 2−97
− Curve follower (FOLL), 2−108
− CW/CCW/Quick stop (R/L/Q), 2−153
− dead band (DB), 2−80
− Delay (DIGDEL), 2−91
− Delay (PT1), 2−150
− designation, 2−33
− Device control (DCTRL), 2−82
Change ofparameter set (PAR), 2−85
Controllerinhibit (CINH), 2−84
Operation inhibited(DISABLE), 2−84
Quick stop (QSP), 2−83
TRIP−RESET, 2−85
TRIP−SET, 2−84
− diameter calculator (DCALC), 2−81
− differentiation (DT1−1), 2−96
− Digital frequency input (DFIN), 2−87
− Digital frequency output (DFOUT), 2−88
− Digital frequency processing (DFSET), 2−90
− Digital frequency ramp function generator (DFRFG), 2−89
− Digital inputs (DIGIN), 2−94
− Digital outputs (DIGOUT), 2−95
− Digital status signals (STAT), 2−159
− display code, 2−34
− Edge evaluation (TRANS), 2−160
− Flipflop (FLIP), 2−106
− Freedigital outputs (FDO), 2−99
− Holding brake (BRK), Set pulse inhibit, 2−66
− Holdingbrake (BRK), 2−63
Close brake, 2−64
Disengaging the brake, 2−65
− input name, 2−33
− input symbol, 2−33
− integrator (INT), 2−110
− Internal motor control
Vector control (MCTRL2), 2−114
with V/f characteristic control (MCTRL1), 2−113
− Inversion (ANEG), 2−56
− Limitation (LIM), 2−112
− Logic AND (AND), 2−53
− Logic NOT (NOT), 2−133
− Logic OR , 2−141
− mains failure control (MFAIL), 2−115
− Monitor outputs of monitoring system (MONIT), 2−128
− motor phase failure detection (MLP), 2−127
− Motor potentiometer (MPOT), 2−129
− Oscilloscope function (OSZ), 2−144
− output name, 2−34
− output symbol, 2−34
− parameterisation code, 2−34
− Process controller (PCTRL), Controller for pressure, level, dancer position,
2−145
− Programming of fixed setpoints (FIXSET), 2−104
− Ramp function generator (RFG), 2−151
− removing a connection, 2−38
− S−ramp function generator (SRFG), 2−156
− Sample & Hold (S&H), 2−154
− signal types, 2−32
− speed preconditioning (NSET), 2−135
− Square−root calculator (SQRT), 2−155
− system bus (CAN−IN), 2−68
− system bus (CAN−OUT), 2−68
G
Global Drive Control, configuration by means of, 2−3
H
Holdingbrake (BRK), 2−63
I
Integrator (INT), 2−110
Internal motor control
− V/f characteristic control (MCTRL1), 2−113
− with vector control (MCTRL2), 2−114
Inversion (ANEG), 2−56
J
JOG setpoint, 2−7 , 2−15
JOG setpoints, 2−137
L
Limitation (LIM), 2−112
Logic NOT (NOT), 2−133
Logic OR , 2−141
M
Main setpoint channel, 2−137
Mains failure control, 2−118
Mains failure control (MFAIL), 2−115
− fast mains recovery (KU), 2−126
− mains failure control, 2−118
− mains failure detection, 2−116
− restart protection, 2−125