Rockwell Automation 8520 9/Series CNC Lathe - Manual (Page 808)

Error and System Messages
Appendix B
B-8
Message Description
CHARACTERS MUST FOLLOW WILDCARD You have used incorrect search string syntax in the PAL search monitor utility.
CHECKSUM ERROR IN FILE The file (AMP, PAL) being downloaded from a storage device has a checksum error. The file
cannot be used.
CIRCLE MID-POINT NOT ENTERED The center-point of an arc is not entered in a circular programming block. Circular blocks
require programming either an R or an I, J, K in the block.
CIRCULAR BLOCK NOT ALLOWED When activating cutter compensation, you cannot program a circular block as the first block or
as the last block prior to deactivating cutter compensation.
CIRCULAR NOT ALLOWED AFTER SKIP A circular move cannot immediately follow a G31 or G37 series skip block. Only linear moves
are permitted as the next move following a G31 or G37 type code.
CIRCULAR PROGRAMMING ERROR A circular motion was programmed incorrectly. Typically this occurs from incorrectly
programming an R or I, J or K value.
CODING ERROR A system software error has occurred. Consult Allen-Bradley customer support services.
COM COMMAND TABLE IS CORRUPTED Restore the flash version of the output command table.
COM CONFIGURATION TABLE IS CORRUPTED Restore the flash version of the communication configuration table.
COMM ERROR WHILE PROCESSING HOST REQUEST A communication error occurred between your PC and 9/Series while performing an update
utility. Retry at a lower baud rate. If that does not work check communication ports, connections
and cable wiring.
COMMUNICATION TIME-OUT The time allowed for a peripheral device to respond has elapsed. Check cable connections and
device set-up.
COMMUNICATIONS DISPLAY PAGE ENABLED When a remote host enables the 9/Series remote operator display screen, this message is
displayed.
COMMUNICATIONS LINK IS DOWN A problem was detected in the communications line. Check the cables and retry the
download/upload.
COMPLETED WITH ERROR(S) A QuickCheck syntax check operation has completed the check of the currently active program
and found one or more errors. Some editing of the program is required.
COMPLETED WITH NO ERRORS A QuickCheck syntax check operation has completed the check of the currently active program
and found no syntax errors.
CONFIGURATION EXCEEDS AVAIL MEMORY This error occurs when the amount of available control memory drops below what is required to
maintain a minimum 5 block setup buffer for program execution. The system is held in E-Stop
when this error occurs. You may either chose to add more memory to your system or
re-configure your system by decreasing the watch list allocation (in AMP) for OCI systems.
CONTINUE NOT ALLOWED An attempt was made to continue a program search when no character string was entered. This
can occur when an error is generated by the program being searched and the control cannot
continue the search of the program correctly.
CONTROL RESET NOT ALLOWED The Control Reset Request was not honored by the control (e.g., a Control Reset Request
during Cycle Suspended state).
CORRUPTED PROGRAM FOUND & DELETED Program was found to be corrupted and not usable. This program was deleted.
CPU #2 DUALPORT RAM FAILED The DUALPORT RAM memory shared between the 68000 main processor and the Z80 I/O ring
processor has failed. (two 98030’s instead of the 68000 and Z80 on 9/230, 9/260, and 9/290
controls)
CPU #2 EXEC IS BAD/MISSING CPU #2 exec is not in flash; you must use update utility to load it (9/290 only). Consult
Allen-Bradley customer support services.
CPU #2 EXEC WILL NOT START CPU #2 is halted and will not start to execute its exec (9/290 only). Consult Allen-Bradley
customer support services.
CPU #2 HARDWARE ERROR #2 The 68030 main processor has detected a bus error. Consult Allen-Bradley customer support
services (9/290 only).
CPU #2 HARDWARE ERROR #3 The 68030 main processor has detected a spurious interrupt. Consult Allen-Bradley customer
support services (9/290 only).