Rockwell Automation 8520 9/Series CNC Lathe - Manual (Page 822)

Error and System Messages
Appendix B
B-22
Message Description
INVALID PROGRAM NUMBER (P) A program number called by a sub-program or paramacro call is invalid. A P-word that calls a
sub-program or paramacro can only be an all-numeric program name as many as 5 digits long.
The O-word preceding the numeric program number in control memory cannot be entered with
the P-word.
INVALID REMOTE NODE NAME An error occurred in G05 DH+ communications block.
INVALID REMOTE STATION TYPE An error occurred in G05 DH+ communications block.
INVALID REPEAT COUNT (L) An L parameter that programs the number of times a paramacro or other operation is to be
repeated was programmed incorrectly or out of the legal range. The L-word for repeat count
must be a whole, positive number. Decimal values and negative values are invalid. The
maximum value of an L-word is 9999.
INVALID ROUGHING CYCLE (P/Q) WORD VALUE When executing a roughing cycle, the starting or ending sequence number of the contour
defining blocks cannot be found in the currently executing program. The sequence number of
the contour blocks is programmed using the P and Q words. These blocks can be anywhere in
the program provided they are resident in the same program, sub-program, or paramacro
program that contains the calling block.
INVALID SCALE FACTOR (P-WORD) An invalid scale factor has been specified. The P-word has a range of 0.0001 to 999.99999.
INVALID SERVO HARDWARE TYPE The AMP servo parameter that selects the servo type does not match the hardware found on
the control when the AMP file is downloaded. Either AMP is misconfigured or the servo
hardware installed on your system is not correctly installed or not of the correct type.
INVALID SHAFT POCKET When entering a custom tool in the random tool table, an attempt was made to assign a shaft
pocket position that is not in the range of the number of pockets assigned to the tool. The shaft
pocket number must be equal to or less than the number assigned for the number of pockets.
INVALID SHAFT POCKET VALUE A program is attempting to enter a custom tool in the random tool table with a invalid shaft
pocket position (not in the range of the number of pockets assigned to the tool). The shaft
pocket number must be equal to or less than the number assigned for the number of pockets.
The shaft pocket value is assigned in a G10.1 block following the R-word.
INVALID SPCMD VALUE A invalid special command error typically occurs when the servo PROMs are not compatible
with the main processor PROMs. Check the software version numbers and contact
Allen-Bradley customer support services.
INVALID SYMBOL NAME An error occurred in G05 DH+ communications block.
INVALID T-CODE FORMAT This is an invalid T-Code Format
INVALID_THREAD_ANGLE An attempt was made to program an angle that is outside the allowable range, which is 0
through 120 degrees.
INVALID THRESHOLD RATE An invalid threshold percentage was entered for a tool group while setting tool management
data. The threshold percentage must range between 0 and 100 percent. Only whole positive
numbers can be entered. If using a G10 block, the threshold percentage is entered with a
Q-word.
INVALID TIME FORMAT MUST BE HH:MM:SS An invalid time format was entered. The time format must be hour / minute / second
(HH/MM/SS).
INVALID TOOL AXIS This is an invalid Tool Axis.
INVALID TOOL CUTTER COMPENSATION NUMBER An attempt was made to enter a tool radius offset number, for cutter compensation or TTRC, in
the tool life management table that is larger than the maximum offset number allowed. If the
tables are being loaded by a G10 program, the radius offset is entered with a D-word in the
block.
INVALID TOOL DIAMETER VALUE An invalid tool diameter value was entered in a program block.
INVALID TOOL GROUP An attempt was made to create a tool group greater than 200 in the tool management tables. A
maximum of 200 tool groups can be used. If loading the tables using a G10 program, the tool
group number is entered using a P-word.