Comtech EF Data SDM-300A User Manual
Page 425
SDM-300A Satellite Modem
Revision 6
Remote Control Operation
MN/SLM3650.IOM
A–33
Demod/
Decoder
Config.
Program
Status
Command:
Response:
<add/DCP_’cr’
>add/DCP_’cr’
SMT_xxxxxxx’cr’
IROT_xxxxx’cr’
MOM_xxxxxxx’cr’
BERT_xxxx’cr’
DT_xxxx’cr’
DDT_xxx’cr’
RCEN_1_xxxx’cr’
(Note 4)
RCDR_1_xxxx.x’cr’ (Note
5)
RCEN_2_xxx’cr’
(Note 4)
RCEN_3_xxxx’cr’
(Note 4)
RCDR_3_xxxx.x’cr’ (Note
6)
RCCP_3_yyy’cr’ (Note
6)
RCDP_3_yyy’cr’ (Note
6)
RCEN_4_xxxx’cr’
(Note 4)
RCDR_4_xxxx.x’cr’ (Note
7)
RCCP_4_yyy’cr’ (Note
7)
RCDP_4_yyy’cr’ (Note
7)
DF_nnn.nnnnnn’cr’
DR_nnnn_mmmm.mmm’cr’
DE_xxx’cr’
DDEC_xxx’cr’
RFL_xxx’cr’
IFL_xxx’cr’
SCF_snnnnn’cr’
SWR_nnnnn’cr’
SR_xxx’cr’
ILT_xxx’cr’
ERF_nnnnn.n’cr’
BC_xxx’cr’
RCP_xxxx’cr’
BBL_xxx’cr’
ILB_xxx’cr’
ICFR_xxxx’cr’
IRFS_T1_ssss’cr’
IRFS_E1_ssss’cr’
IBP_xxx’cr’
IRE_xxxxxx’cr’
RDF_xxxx’cr’
ISCL_RX1_nnn’cr’
ISCL_RX2_nnn’cr’
RDP_xxxx’cr’
IDF_xxxxxx’cr’ (Note
1)
ICRC_xxx’cr’ (Note
1)
IBS _nnnnnn’cr’
BICA_dd;cc_dd;cc...’cr’ (Note 1)
System Modem Type
Interface Receive Overhead Type
Modem Operation Mode
BER Threshold
Demodulator Type
Demodulator Decoder Type
Flex Mux RX Channel #1 Enable
Flex Mux RX Channel #1 Data Rate
Flex Mux RX Channel #2 Enable
Flex Mux RX Channel #3 Enable
Flex Mux RX Channel #3 Data Rate
Flex Mux RX Channel #3 Clock Phase
Flex Mux RX Channel #3 Data Phase
Flex Mux RX Channel #4 Enable
Flex Mux RX Channel #4 Data Rate
Flex Mux RX Channel #4 Clock Phase
Flex Mux RX Channel #4 Data Phase
Demodulator Frequency
Demodulator Rate
Descrambler Enable
Differential Decoder
RF Loopback
IF Loopback
Sweep Center Frequency
Sweep Width Range
Sweep Reacquisition
Interface Loop Timing
External Reference Frequency
Buffer Clock
Receive Clock Phase
Baseband Loopback
Interface Loopback
Interface Coding Format Receive
Interface Receive T1 Frame Structure
Interface Receive E1 Frame Structure
Interface Buffer Programming
Interface Read Error (RX 2047)
Receive Data Fault
Service Channel Level RX1
Service Channel Level RX2
Receive Data Phase
Insert Data Format
Insert E1 CRC Enable
Interface Buffer Size
Bulk Insert Channels Assignment