Yaskawa E7L Drive Bypass - Manual (Page 299)

Index - 9
Protective Functions.............................................. C-4, A-22
PWM Frequency - See Carrier Frequency ...................... A-8
Q
-QUICK- Setting Menu ......................................... 3-11, 3-16
R
Ramp to Stop .......................................................... 5-13, A-4
Rated Current, Motor . 4-4, 4-7, 5-47, 5-80, A-11, A-25, B-3
READ ..........................................................5-78, 6-18, A-25
Receiving.......................................................................... 1-6
REF Indicator ................................................................... 3-4
Reference Limits (See Frequency) ................5-41, 6-24, A-9
Reference Selection, AUTO, HAND ......................3-3, 4-12
Reference Source.......................... 1-14, 4-12, 5-12, 5-6, A-4
Relays, Digital Output.......2-9, 2-19, 2-20, 2-24, 5-53, A-15
Remote Transfer to Bypass .........2-16, 2-20, 3-8, 4-10, 4-14
Removing the Drive ......................................................... 7-7
Replacing the Drive.......................................................... 7-9
Replacing the H/O/A Control Panel................................. 7-4
Replacing PCB A2 ........................................................... 7-4
Replacement Parts ................................................. F-2 to F-5
See Spare Parts Ordering ..................Inside Back Cover
RESET Key ...................................................................... 3-3
Resistance, Motor Line-to-Line .....................................A-11
Resistor Terminating ............................. 2-15, 2-17, 5-6, D-4
Resonance............ 1-19, 4-7, 5-41, 5-42, 6-23, 7-2, A-9, C-4
Resources Available .............................................................v
REV Indicator .................................................................. 3-4
Reverse Operation ............................ 3-4, 4-7, 4-8, 5-11, A-4
Prohibiting..............................................5-16, 6-21, A-4
Programming........................................................... 5-16
Ride-thru, Momentary Power Loss ...... 5-60, A-19, B-3, C-4
“Right Arrow” Key .......................................................... 3-3
RS-485/422.........................................5-48, A-11, A-18, D-1
Communication Wiring................................... 2-19, D-3
Control Circuit Terminals ..............................2-14, 2-21
Parameters ......................... 2-14, 5-4 to 5-9, A-11, A-18
Terminating Resistance ................................... 2-15, D-3
RTS Control Selection..................................2-14, A-18, D-5
Run Delay............................................................... 5-17, A-4
Run Command
During Program............................................... 5-17, A-4
External, Troubleshooting....................................... 6-20
Selection...........................3-3, 3-4, 4-12, 5-4, 5-13, A-4
Source............................................ 1-11, 4-12, 5-6, 5-13
Status ......................................................................... 3-8
Terminals........................................................2-14, 2-21
RUN Indicator ...........................................................3-2, 3-5
Running
Signal (Digital Output).............................................. 2-9
Stall Prevention during.........................5-63, 6-21, A-20
S
Safety Circuit ...............2-10, 2-20, 3-7, 4-2, 4-4, 4-13, A-14
Scaling Display
Digital Operator.............................................5-73, A-23
PI Setpoint .......................................................5-33, A-6
Schematic Diagram........................................ 2-7, 2-18, 2-22
S-Curve Characteristic.....................................................A-7
SEQ...................................................................................3-4
Selector Keys ........................................1-10, 3-2, 4-10, 4-12
Sequence Parameters .......................................................A-4
Serial Communications.......................................D-2 to D-26
Address .....................................................................D-5
APOGEE FLN...........................................D-20 to D-26
Baud Rate .............................................. A-18, D-2, D-5
Drive Node Address .................................................D-5
Metasys N2 ................................................D-16 to D-19
Monitor Only .............................................................5-7
Parameters ............................................A-11, A-18, D-5
Run Command (Com. Option) ................................5-13
Self-Diagnosis Function .........................................D-15
Serial Number ........................................................... 1-6, 1-7
Setpoint (PI Function).......................5-23 to 5-29, 5-33, A-6
Boost Setting....................................................5-35, A-6
Display Scaling................................................5-33, A-6
Selection ................................................ 5-25, 5-33, A-6
Value ................................................................5-33, A-6
SHIFT/RESET Key ..........................................................3-3
Shield Wire Grounding ............ 2-5, 2-12, 2-15, 2-18 to 2-20
Shipping Damage..............................................................1-6
Short Circuit Protection, Branch........i, 1-8, 1-12, E-2 to E-4
Skip Frequency .............................4-7, 5-42, 6-23, 6-24, A-9
Slave....................................................................D-3 to D-14
Sleep Function - See PI Function, Sleep.................5-32, A-6
Smoke Purge .............1-10, 2-16, 2-20, 3-7, 3-10, 4-10, 4-14
Snooze Function - See PI Function, Snooze...........5-35, A-6
Soft Charge Contactor...........................6-12, 6-15, 6-26, 7-3
Soft Charge Resistor ............................................... 6-26, 7-3
Soft CLA Selection........................................................A-22
Soft Start ..........................................................................A-7
Software Number (U1-14) .............................................A-27
Spare Parts .............................................................F-1 to F-5
SPEC.................................................................................1-7
Specifications........................................................ C-1 to C-4
Design (o2-09)........................................................A-25
General...................................................................... C-4
Speed
Agreement .......................................... 5-67, A-15, A-21
Control Accuracy...................................................... C-4
Range ........................................................................ C-4
Speed Command - See Frequency Reference
0-10Vdc ........................ 2-11, 2-17, 2-20, 4-7, 5-6, 5-56
4-20mA......................... 2-11, 2-17, 2-20, 4-7, 5-6, 5-56
Limits..................................................... 5-41, 6-24, A-9
Loss Detection ...............................................5-64, A-21
Selection ................................ 3-3, 4-12, 5-6 to 5-9, A-4