Lingenfelter L460240000 Lingenfelter NCC-002 Nitrous Control Center v1.5 - Manual (Page 16)

Lingenfelter NCC-002 Nitrous Control Center Installation and Operating Instructions 15
3 Installation of the NCC-002 Nitrous Control Center
The following subsections detail the installation of both the NCC-002 controller in the vehicle, as well as the
Nitrous Control Center and NCC Controller Flash Utility software programs onto a personal computer. In the
following subsections that cover the installation of the controller itself, several wiring configurations have been
provided to give you ideas of how the controller can be installed. Please note that a combination of these
configurations may be necessary to achieve your desired operation. In the subsections that cover the
installation of the Nitrous Control Center and NCC Controller Flash Utility software, the installation steps
described should be explicitly followed in order to properly install the software. If the software is being installed
on a Windows Vista or Windows 7 equipped computer, some of the screens and dialog boxes may differ slightly
from the screen shots provided in this manual as the example installation was done on a Windows XP equipped
computer.
3.1 Installation of the NCC-002 Hardware
The following sub-sections detail the installation of the NCC-002 Nitrous Controller in a vehicle. Each sub-
section will have a description of the configuration and a wiring diagram. Please note that the following
configurations represent just a small number of possible wiring configurations for the NCC-002 Controller. The
optional NCC-002 wire harness (PN: L480310000) is composed of 22 color-coded wires (10 feet in length) that
are all individually labeled on their insulation. Make sure that each of the wires required for the desired
configuration are correctly installed into their respective terminals. If you choose not to use the optional NCC-
002 wire harness, use the supplied terminals to make your own harness. The terminals on the NCC-002 will
accept 16-22 AWG wire. It is recommended that the controller ground wires, the controller +12 volt power
wires, and the solenoid ground wires should all be 16 gauge wire. All other wires can be 20 gauge wire. Refer
to
Appendix C: Tables and Diagrams for a chart showing the recommended gauge for a length of wire based on
current draw and voltage drop. After crimping a terminal to one end of the wire, use heat shrink tubing to seal
and insulate the end going to the NCC-002 to reduce the chance of a short circuit.
The configurations that will be shown in the following sub-sections are:
•
Progressive Nitrous Without Fuel Control
•
One Stage of Progressive Nitrous and Fuel
•
Two Stages of Progressive Nitrous and Fuel
•
NCC-002 Controlling the Solenoids Via Nitrous Solenoid Driver
•
NCC-002 Controlling Nitrous Solenoids Via Relays
•
NCC-002 Controlling a Bottle Heater
•
NCC-002 Connected to the LPE LNC-2000 Launch Controller
•
NCC-002 Connected to the LNC-2000 for Simple On/Off Control
•
NCC-002 Connected to the Pin on the ECM for EFILive Nitrous Operating System and Fuel Control
•
Connecting the NCC-002 to Throttle Position Sensors on Mechanical and Electronic Throttle Vehicles
•
NCC-002 Connected to the Clutch Position Sensor
•
NCC-002 Connected to the Clutch Position Switch
•
Converting a CPP Sensor Signal Into a 12 Volt Signal Via Conversion Module
NOTE: The wire colors in the wiring diagrams below will most likely differ from the wiring in your
vehicle. Identify the wires of all applicable components in your vehicle and confirm their individual
functions before beginning to wire the NCC-002 controller.
WARNING: LPE recommends that Nitrous safety solenoids be used anytime the primary solenoids are
pulse-width modulated. The use of nitrous safety solenoids allow the flow of nitrous to be terminated in
the event that either of the primary nitrous solenoids get stuck open.
NOTE: The wiring of the NCC-002 Nitrous Controller may require additional lengths of wire depending
on where the NCC-002 will be mounted on the vehicle.
NOTE: The wire harness colors described in this installation manual assume that you are installing the
optional NCC-002 wiring harness.
Refer to
Appendix C: Tables and Diagrams for assistance in determining the proper RPM pulse count, engine
speed wiring locations, vehicle speed wiring locations, etc.