Lenze EVS93xx CrossCutter - Manual (Page 212)

Cross Cutter
Appendix
 Prepared Solution Servo PLC / ECSxA 1.1 EN 6-44
Possible settings: Code
Default Selection
Comment
Display code: Status of calculation sequence for new start/stop
length
0 Calculation ok.
1 • No LC9 file found.
• Profile data not found in absolute data model.
• Read error when accessing profile data.
2 Selected motion profile not found.
4 The angle of motion of the knife drum for the
asynchronous motion phase is less than or equal to zero
(check y final value of basic profile and cutting angle!).
8 A value of zero has been entered for the knife drum's
cutting circle circumference.
16 The preset cutting length is less than the material length
corresponding to the cutting angle.
32 The selected motion profile contains fewer than 20
interpolation points.
64 The selected motion profile does not start at zero
(0.0000/0.0000).
128 Cutting angle too small.
256 The y final value of the basic profile does not correspond
to value 360.0000[°]/n
cuts/rev
.
(n
cuts/rev
= Number of knives on knife drum, values of 1, 2,
3, 4, 5 or 6 are possible)
512 Error during internal read access to C0011/000
C3664/
000
- - {1} -
If the status variable is exhibiting non-zero values, the calculated
variables may exhibit invalid values, in which case it will not be
possible to use them subsequently in the control program!
C3665/
000
100 80... {1%} ... 120
Cutting speed adaptation factor
Enable torque precontrol.
TRUE
Torque precontrol is enabled.
C3666/
000
0 0 {1} 1
FALSE Torque precontrol is disabled.
C3667/
000
10.0 -200.0... {1%} ... 200.0
Adaptation factor for torque precontrol
C3668/
000
370.0000 0.0000 {1.0000
m_units}
214000.0000 Distance measured from mark sensor to 6 o'clock position of
knife.
C3669/
000
60.0000 0.0000... {0.0001
m_units}
... 214000.0000
Size of mark window
C3670/
000
1 0 ... {1} ... 65535 Number of cycles permitted without a mark signal appearing in
the mark window. A warning signal is generated if this number is
exceeded.
C3671/
000
- - - - Display code: X trimming outputvalue scaled in 1.0000 m_units
C3672/
002
20.0000 0.0100... {0.01 s} ... 130.0000
Acceleration ramp time for position trimming
C3672/
003
20.0000 0.0100... {0.01 s} ... 130.0000
Deceleration ramp time for position trimming
C3673/
001
200.0000 0 ... {1 rpm} ...15000
Speed for position trimming in a positive direction
C3673/
002
200.0000 0 ... {1 rpm} ...15000
Speed for position trimming in a negative direction
C3674/
000
0.0000 -214748.0000... {0.0001
m_units}
... 214748.0000
Selection of the absolute trimming target position
C3676/
000
10.000 0.000... {0.001 s} ... 999.999
Acceleration ramp time for inching trimming
C3677/
000
10.000 0.000... {0.001 s} ... 999.999
Deceleration ramp time for inching trimming
C3678/
000
6 0 ... {1 rpm} ...15000
Selection of the inching speed
C3679/
000
0.0000 0.0000... {0.0001
m_units}
... 214000.0000
Distance from reject gate to cutting position
C3680/
000
0 0 ... {1 ms} ... 65535
Switching dwell time (switching delay time) of reject gate