Lenze EVS93xx CrossCutter - Manual (Page 229)

Cross Cutter
Appendix
 Prepared Solution Servo PLC / ECSxA 1.1 EN 6-61
Error
number
Error code Cause Remedy
The value set in code C0122/000 is too
low. Increase the value in code C0122/000.
Overtemperature detection by
PTC/KTY: Motor too hot due to
continuous overload/overcurrent Check the drive dimensioning.
No PTC/KTY connected
Connect PTC/KTY.
Deactivate the OH7 error by setting code C0584/000
= 3).
57 OH7
The value set in code C0121/000 is too
low. Increase the value in code C0121/000.
Overtemperature detection by
temperature contact: Motor too hot
due to continuous
overload/overcurrent Check the drive dimensioning. 58 OH8
No temperature contact connected
Connect a temperature contact to terminals T1/T2.
Deactivate the OH8 error by setting code C0585/000
= 3).
61 CE0 Fault during transmission of control
commands via AIF interface (e.g.
PROFIBUS DP) Plug the automation module in securely.
Screw the automation module tight.
62 CE1 CAN-IN1 channel receiving no data or
faulty data Check the CAN bus line (connector X4).
Check the CAN terminating resistors (on the first and
last CAN nodes).
Check the configuration of the CAN node sending to
CAN-IN1.
Check the voltage supply of the CAN node sending
to CAN-IN1.
Check and if necessary increase the monitoring time
in code C0357/001.
63 CE2 CAN-IN2 channel receiving no data or
faulty data Check the CAN bus line (connector X4).
Check the CAN terminating resistors (on the first and
last CAN nodes).
Check the configuration of the CAN node sending to
CAN-IN2.
Check the voltage supply of the CAN node sending
to CAN-IN2.
Check and if necessary increase the monitoring time
in code C0357/002.
64 CE3 CAN-IN3 channel receiving no data or
faulty data Check the CAN bus line (connector X4).
Check the CAN terminating resistors (on the first and
last CAN nodes).
Check the configuration of the CAN node sending to
CAN-IN3.
Check the voltage supply of the CAN node sending
to CAN-IN3.
Check and if necessary increase the monitoring time
in code C0357/003.
65 CE4 Controller has received too many
faulty telegrams via the CAN bus and
has disconnected itself from the bus. Check the baud rates of all nodes.
Check the wiring:
-
Check the bus terminating resistors.
- Check the shield connection on the cables.
- Check the PE connection.
- Check the bus load.
- Reduce the baud rate (CAUTION: Take the CAN
bus cable lengths into account).
66 CE5 CAN time-out (gateway function
C0370)
Check the settings in code C0370/000.
70 U15 Undervoltage internal 15 V supply
voltage
Check the control voltage for voltage fluctuations or
voltage dips.
Processor is overloaded or a program
flow error has occurred. Reduce the processor load: Remove function blocks
which are not required from the processing table
(C0465/0xx).
Significant interference injections on
the control cables Install shielded control cables.
71 CCr
Earth loops in the wiring Make sure that the wiring is EMC-compliant (see
"9300" System Manual, p. 4-34).
72 Pr1 Error transmitting the parameter set
CAUTION: The default setting is
loaded automatically! Set the required parameters and save them to non-
volatile EEPROM via code C0003/000.
73 Pr2 Error transmitting the parameter set
CAUTION: The default setting is
loaded automatically! Set the required parameters and save them to non-
volatile EEPROM via code C0003/000.