GE Industrial Solutions EntelliPro ES - Manual (Page 108)

CHAPTER 2: INSTALL ATION/CONFIGURATION
EPOS MOTOR MANAGEMENT SYSTEM- INSTRUCTION MANUAL 2.83
Tables below show the default configuration for all typicals.
Motor Starter Standard Configuration
EntelliPro ES3
Full-voltage
non-
reversing
Full-voltage
reversing
Star-delta
non-
reversing
Star-delta
reversing
Softstarter
Softstarter
reversing
Breaker Dahlander
Pole-
changer
Actuator
Solenoid
valve
Feedback via contact Activated Activated Activated Activated N/A Activated Activated Activated Activated Activated Activated Activated
Feedback via current Activated Activated Activated Activated N/A Activated Activated N/A Activated Activated Activated N/A
Direct Switch over without OFF command N/A Deactivated N/A N/A N/A Deactivated N/A Activated Activated Deactivated N/A
Current depending YD Switch Over N/A N/A Activated N/A N/A N/A N/A N/A N/A N/A N/A
Soft Stop Timer N/A N/A N/A N/A Deactivated Deactivated N/A N/A N/A N/A N/A
Bypass Control N/A N/A N/A N/A Activated Activated N/A N/A N/A N/A N/A
External Soft Starter Fault N/A N/A N/A N/A Activated Activated N/A N/A N/A N/A N/A
MCCB Tripped 2 Configuration (Alarm or
No-Alarm)
N/A N/A N/A N/A N/A N/A no alarm N/A N/A N/A N/A
Breaker Trip Reset from EntelliPro ES N/A N/A N/A N/A N/A N/A Activated N/A N/A N/A N/A
MCCB Feedback N/A N/A N/A N/A N/A N/A Activated N/A N/A N/A N/A
Torque Switch N/A N/A N/A N/A N/A N/A N/A N/A N/A Disable N/A
Switch OFF at Limit Switch N/A N/A N/A N/A N/A N/A N/A N/A N/A Activated N/A
Switch OFF at Current Threshold N/A N/A N/A N/A N/A N/A N/A N/A N/A Deactivated N/A
Switch OFF at Torque Switch N/A N/A N/A N/A N/A N/A N/A N/A N/A Deactivated N/A
Enable Modbus RTU Control Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
Enable Profibus DP Class 2 Control Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
Enable Hardwired Control Disable Disable Disable N/A Disable Disable Disable Disable Disable Disable Disable
bit 1 - Class1 n bit 0r (n+1) bit n bit n bit n bit N/A n bit n bit n bit n bit n bit n bit n bit
bit 2 - Level/Edge Level Level Level N/A Level Level Level Level Level Level Level
bit 3 - Inverted OFF / Non-Inverted OFF non non non N/A non non non non non non non
bit 1 - Hardwire n bit 0r (n+1) bit (n+1) bit (n+1) bit (n+1) bit N/A (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit
bit 2 - Hardwire Level/Edge Edge Edge Edge N/A Edge Edge Edge Edge Edge Edge Edge
Thermistor Line Broken/Shorted Supervision. Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
Drawer Position Supervision Deactivated Deactivated Deactivated N/A Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated
Drawer Position 1 bit Modus / 2 bit Modbus N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
Modbus Failure Detection Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
ATEX Activated Deactivated Deactivated Deactivated N/A Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated
bit 5 - Remote OFF always valid Deactivated Deactivated Deactivated N/A Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated
bit 6 - Block Local Switch ON Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
Alarm Setting
Overload Enable Enable Enable N/A Enable Enable Disable Enable Enable Enable Enable
Phase Loss Enable Enable Enable N/A Enable Enable Disable Enable Enable Enable Disable
Ground Fault Enable Enable Enable N/A Enable Enable Disable Enable Enable Enable Disable
Unbalance Load Enable Enable Enable N/A Enable Enable Disable Enable Enable Enable Disable
Thermsitor Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
Emergency Stop Enable Enable Enable N/A Enable Enable Disable Enable Enable Enable Enable
Limit Switch Disable Disable Disable N/A Disable Disable Disable Disable Disable Enable Enable
Safety Circuit Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
Main Circuit Enable Enable Enable N/A Enable Disable Enable Enable Enable Enable Enable
Control Circuit Enable Enable Disable N/A Disable Disable Disable Disable Enable Disable Disable
Switch Position Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
Underload Current Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
Overload Current Enable Enable Enable N/A Enable Enable Enable Enable Enable Enable Enable
External Supervisory Enable Enable Enable N/A Enable Enable Enable Enable Enable Disable Enable
Long Start Time Enable Enable Enable N/A Enable Enable Enable
e
Enable Enable Enable i Disable
Input Mapping
Input 99 Mapping
Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
N/A
Contactor 1
Feedback
Contactor 1
Feedback
MCCB ON
Feedback Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
Input 99 High/low Activation Active High Active High Active High N/A Active High Active High Active High Active High Active High Active High Active High
Input 98 Mapping External
Supervision
Contactor 2
Feedback
Contactor 2
Feedback
N/A Main Circuit
Feedback
Contactor 2
Feedback
Breaker
Ready to
Switch ON
Contactor 2
Feedback
Contactor 2
Feedback
Contactor 2
Feedback
Main Circuit
Feedback
Input 98 High/Low activation Active Low Active High Active High N/A Active Low Active High Active High Active High Active High Active High Active Low