GE Industrial Solutions EntelliPro ES - Manual (Page 167)

4.30 EP OS MOTOR MANAGEMENT SYSTEM – INSTRUCTION MANUAL
CHAPTER 4: COMMUNICATION
Input
Register
Address
Data
Size
Parameter Name Units Scale Format Note
89
(cont.)
16 bit 133 = Emergency Stop Fault Reset
134 = Limit Switch Fault Reset
135 = Safety Circuit Fault Reset
136 = Main Circuit Fault Reset
137 = Control Circuit Fault Reset
138 = Switch Position Fault Reset
139 = Underload Current Fault Reset
140 = Overload Current Fault Reset
141 = External Supervision Fault Reset
142 = Long Start Time Fault Reset
143 = Typical Specific Fault Reset
144 = Thermal Overload Warning Reset
145 = Thermistor Warning Reset
146 = Ground Fault Sum Warning Reset
147 = Unbalanced Load Warning Reset
148 = Phase Loss Warning Reset
149 = Emergency Stop Warning Reset
150 = Limit Switch Warning Reset
151 = Safety Circuit Warning Reset
152 = Main Circuit Warning Reset
153 = Control Circuit Warning Reset
154 = Switch Position Warning Reset
155 = Underload Current Warning Reset
156 = Overload Current Warning Reset
157 = External Supervision Warning Reset
158 = Long Start Time Warning Reset
159 = Typical Specific Warning Reset
160 = Contactor 1 Feedback Status Off
161 = Contactor 2 Feedback Status Off
162 = ESS DP Parameter Mode Off
163 = Switch Protected Status Off
164 = Start Attempt Status Off
165 = Drawer Ready Status Off
166 = General Warning Status Off
167 = General Fault Status Off
168 = Safety Circuit Status Off
169 = ESS DP Local Mode Status Off
170 = ESS DP Remote Mode Status Off
171 = Drawer Operation Mode Status Off
172 = Drawer Test Mode Status Off
173 = Limit Switch 1 Status Off
174 = Limit Switch 2 Status Off
175 = General Device Error Status Off
176 = Feedback Identification Status Off
177 = Class 1 Failure Off
178 = Modbus Failure Off
179 = Bypass Switched On Status Off
180 = Switching 1 Progess Status Off
181 = Switching 2 Progress Status Off
182 = Breaker Tripped Status Off
183 = Status Charged Status Off
184 = Torque Switching 1 Status Off
185 = Torque Switching 2 Status Off
186 = Start Phase Off
187 = Run Phase Off
188 = Thermistor Line Not Broken
189 = Thermistor Line Not Shorted
190 = Reserved Status 30 Off
191 = Reserved Status 31 Off
192 = Parameter No Error
193 = Watchdog No Error
194 = EEPROM No Error
195 = Start Attempt No Error
196 = Thermistor Test Not Fail
197 = Modbus ON 1 Off
198 = Modbus ON 2 Off
199 = Class 1 ON 1 Off
200 = Class 1 ON 2 Off
201 = Class 1 OFF Off
202 = Class 2 ON 1 Off
203 = Class 2 ON 2 Off
204 = Class 2 OFF Off
205 = Hardwire ON 1 Off
206 = Hardwire ON 2 Off
207 = Hardwire OFF Off
Unsigned Integer Indicates the event type base on Index selected on holding
regsiter 101
90 16 bit Event Tenths/Hundredths of Seconds Unsigned Integer Event of Input register 89 date and time
91 16 bit Event Seconds Unsigned Integer
92 16 bit Event Minutes Unsigned Integer Event Time Stamp
93 16 bit Event Hours Unsigned Integer Event Time Stamp
94 16 bit Event Date Unsigned Integer Event Date
95 16 bit Event Month Unsigned Integer Event Date
96 16 bit Event Year Unsigned Integer Event Date
97 16 bit “Analog RMS Value Log Data Ready
0 - Data Not Ready to be retrived
1 - Data Ready to be retrived”
Unsigned Integer 0 - Data not ready to be retrieved.
1 - Data ready to be retrieved.