GE Industrial Solutions EntelliPro ES - Manual (Page 158)

EP OS MOTOR MANAGEMENT SY STEM – INSTRUCTION MANUAL 4.21
CHAPTER 4: COMMUNICATION
Holding
Register
Modbus
Size
Variable Description Min Max Step Units Scale Format Default
76 16 bit Time Sync Year
Values to write to Real Time Clock (RTC)
Note:Function code 05 command 181 will be
required after setting registers 76 thru 83.
Year Unsigned
Integer
77 16 bit Time Sync Month Month Unsigned
Integer
78 16 bit Time Sync Date Date Unsigned
Integer
79 16 bit Time Sync Day Da y Unsigned
Integer
80 16 bit Time Sync Hour Hour Unsigned
Integer
81 16 bit Time Sync Minute Minute Unsigned
Integer
82 16 bit Time Sync Second Sec ond Unsigned
Integer
83 16 bit Time Sync Tenths/Hundredths of Seconds 1/10 0th
Seco nd
Unsigned
Integer
90 16 bit ModbusCommunicationSetting;
0 - ModbusComSetting_3008N2
1 - ModbusComSetting_6008N2
2 - ModbusComSetting_12008N2
3 - ModbusComSetting_24008N2
4 - ModbusComSetting_48008N2
5 - ModbusComSetting_96008N2
6 - ModbusComSetting_192008N2
7 - ModbusComSetting_3008O1
8 - ModbusComSetting_6008O1
9 - ModbusComSetting_12008O1
10 - ModbusComSetting_24008O1
11 - ModbusComSetting_48008O1
12 - ModbusComSetting_96008O1
13 - ModbusComSetting_192008O1
14 - ModbusComSetting_3008E1
15 - ModbusComSetting_6008E1
16 - ModbusComSetting_12008E1
17 - ModbusComSetting_24008E1
18 - ModbusComSetting_48008E1
19 - ModbusComSetting_96008E1
20 - ModbusComSetting_192008E1
21 - ModbusComSetting_3008N1
22 - ModbusComSetting_6008N1
23 - ModbusComSetting_12008N1
24 - ModbusComSetting_24008N1
25 - ModbusComSetting_48008N1
26 - ModbusComSetting_96008N1
27 - ModbusComSetting_192008N1
Set Baud Rate, Parity, Data Bits, Stop Bits
Example:
3008N2
300 = Baud Rate
8 = Data Bits
N = No Parity (E = Even Parity, O = Odd Parity)
2 = Stop Bits
0 27 1 Unsigned
Integer
27
91 16 bit Frequency 0 - 50Hz
1 - 60Hz
0 1 1 Unsign ed
120 = 1.2A
e
x100
120 = 1.2A
x100
Integer
92 (L)
32 bit
register 92 = 14. Combine both HEX numbers = 143E8. Convert this number to decimal = 82920. This corresponds to 829.2A base on the x100 scale factor.
Current Sensor Rating Low Speed (Ict_
lowspeed)
Sensor setting
10 65000 1 Amps Unsigned
Integer
120
93 (H)
94 (L)
32 bit Motor Rating Low Speed Motor Load setting
1/6*Ict_
lowspeed
Ict_
lowspeed
1 Amps
Unsigned
Integ er
x100
20 = 0.2A
20
95 (H)
96 (L)
32 bit
Current Sensor Rating High Speed (Ict_
highspeed)
Sensor setti n
127( Interpretation of 32-bit value.
Example register 91 (L = low word) = 1000 register 92 (H = high word) = 20. Convert both registers to HEX: regsiter 91 = 3E8, .
g 10 65000 1 Amps
Unsigned
Integer
120
97 (H)
98 (L)
32 bit Motor Rating High Speed Motor Load setting
1/6*Ict_
highspeed
Ict_
highspeed
1 Amps
Unsign ed x100
20 = 0.2A
Integer
20
99 (H)
100 16 bit
Motor Feedback Enabled
Allows motor to start without any feedback
0 - No feedback required
1 - Feedback required
Read Only register
0 1 1 Unsigned
Integer
1
101 16 Bit Event Read Index
input register112 - Modbus FC 04
Modbus FC 04. Last event index is shown on
Event to be displayed on input register 89 - 96
0 249 1
Unsigned
Integer 0
102 16 bit
Modbus Software / Front Switch Selection
0 - Use Modbus software address set on
holding register 103
1 - Use Modbus address from the front
switches
0 1 1 Unsig ned
Integer
1
103
16 bit ModbusSlaveAddress Modbus Software Slave address 1
247 1
Unsigned
Integer
1
104
16 bit Profibus_ID_Number EntelliPro ES Retrofit = 0x0574
EntelliPro ES = 0x0500
Unsigned
Integer