GE Industrial Solutions EntelliPro ES - Manual (Page 110)

CHAPTER 2: INSTALL ATION/CONFIGURATION
EPOS MOTOR MANAGEMENT SYSTEM- INSTRUCTION MANUAL 2.85
Motor Starter Standard Configuration
EntelliPro ES5
Full-voltage
non-
reversing
Full-voltage
reversing
Star-delta
non-
reversing
Star-delta
reversing
Softstarter
Softstarter
reversing
Breaker Dahlander Polechanger Actuator
Solenoid
Valve
Feedback via contact Activated Activated Activated Activated Activated Activated Activated Activated Activated Activated Activated
Feedback via current N/A Activated Activated Activated Activated Activated N/A Activated Activated Activated N/A
Direct Switch over without OFF
command
N/A Deactivated N/A Deactivated N/A Deactivated N/A Activated Activated Deactivated N/A
Current depending YD Switch Over N/A N/A Activated Activated N/A N/A N/A N/A N/A N/A N/A
Soft Stop Timer N/A N/A N/A N/A Deactivated Deactivated N/A N/A N/A N/A N/A
Bypass Control N/A N/A N/A N/A Activated Activated N/A N/A N/A N/A N/A
External Soft Starter Fault N/A N/A N/A N/A Activated Activated N/A N/A N/A N/A N/A
MCCB Tripped 2 Configuration (Alarm
or No-Alarm)
N/A N/A N/A N/A N/A N/A No alarm N/A N/A N/A N/A
Breaker Trip Reset from EntelliPro ES N/A N/A N/A N/A N/A N/A Activated N/A N/A N/A N/A
MCCB Feedback N/A N/A N/A N/A N/A N/A Activated N/A N/A N/A N/A
Torque Switch N/A N/A N/A N/A N/A N/A N/A N/A N/A Enable N/A
Switch OFF at Limit Switch N/A N/A N/A N/A N/A N/A N/A N/A N/A Activated N/A
Switch OFF at Current Threshold N/A N/A N/A N/A N/A N/A N/A N/A N/A Deactivated N/A
Switch OFF at Torque Switch N/A N/A N/A N/A N/A N/A N/A N/A N/A Deactivated N/A
Enable Modbus RTU Control Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Enable Profibus DP Class 2 Control Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Enable Hardwired Control Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
bit 1 - Class1 n bit 0r (n+1) bit n bit n bit n bit n bit n bit n bit n bit n bit n bit n bit n bit
bit 2 - Level/Edge Level Level Level Level Level Level Level Level Level Level Level
bit 3 - Inverted OFF / Non-Inverted
OFF
Non Non Non Non Non Non Non Non Non Non Non
bit 1 - Hardwire n bit 0r (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit (n+1) bit
bit 2 - Hardwire Level/Edge Edge Edge Edge Edge Edge Edge Edge Edge Edge Edge Edge
Thermistor Line Broken/Shorted
Supervision.
Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Drawer Position Supervision Activated Activated Activated Deactivated Activated Deactivated Deactivated Activated Activated Deactivated Activated
Drawer Position 1 bit Modus / 2 bit
Modbus
2 bit 2 bit 2 bit N/A 2 bit N/A N/A 2 bit 2 bit N/A 2 bit
Modbus Failure Detection Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
ATEX Activated Activated Activated Activated Activated Activated Activated Activated Activated Activated Activated Activated
bit 5 - Remote OFF always valid Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated Deactivated
bit 6 - Block Local Switch ON Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Alarm Setting
Overload Enable Enable Enable Enable Enable Enable Disable Enable Enable Enable Enable
Phase Loss Enable Enable Enable Enable Enable Enable Disable Enable Enable Enable Disable
Ground Fault Enable Enable Enable Enable Enable Enable Disable Enable Enable Enable Disable
Unbalance Load Enable Enable Enable Enable Enable Enable Disable Enable Enable Enable Disable
Thermsitor Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Emergency Stop Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Limit Switch Disable Disable Disable Disable Disable Disable Disable Disable Disable Enable Enable
Safety Circuit Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Main Circuit Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Control Circuit Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Switch Position Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Underload Current Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Overload Current Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
External Supervisory Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable Enable
Long Start Time Enable Enable Enable Enable Enable Enable Disable Enable Enable Enable Disable
Input Mapping
Input 99 Mapping Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
MCCB ON
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
Contactor 1
Feedback
Input 99 High/low Activation Active High Active High Active High Active High Active High Active High Active High Active High Active High Active High Active High
Input 98 Mapping not used Y Contactor
Feedback
Contactor 2
Feedback
Contactor 2
Feedback
Bypass
Feedback
Contactor 2
Feedback
Breaker
Ready to
Switch ON
Contactor 2
Feedback
Contactor 2
Feedback
Contactor 2
Feedback
Drawer
position Test
Input 98 High/Low activation N/A Active High Active High Active High Active High Active High Active High Active High Active High Active High Active High