GE Industrial Solutions EntelliPro ES - Manual (Page 155)

4.18 EP OS MOTOR MANAGEMENT SYSTEM – INSTRUCTION MANUAL
CHAPTER 4: COMMUNICATION
Holding
Register
Modbus
Size
Variable Description Min Max Step Units Scale Format Default
15 16 bit Ground Fault Delay 10 100 10 msec GF Dly
Setting
x 10
10 =
100msec
Unsigned
Integer
10
16
17
32 bit Analog Output Value If analog output is set to 0-20mA - the current
set on this register corresponds to 20 mA.
If analog is set to 4-20mA - the current set on
this register corresponds to 20 mA.
10 520000 1 mA 10 mA
Example:
10 =
100mA
100
= 1A
Unsigned
Integer
20
18 16 bit Overload / Locked Rotor / Stalled Rotator Current threshold 100 800 % Irated
(motor
load) * %
Unsigned
Integer
20
19 16 bit Start Phase Threshold If a current exceed this threshold by a pre-
defined timer set by Timer2, an alarm or fault
will occur.
100 800 % Irated
(motor
load) * %
Unsigned
Integer
20
20 16 bit Under current Threshold If a current falls below this threshold by a
pre-defined timer set by Timer15, an alarm or
fault will occur.
0 = disabled
1 100 % Irated
(motor
load) * %
Unsigned
Integer
20
21 16 bit Typical Specific Threshold Current threshold used on actuator, solenoid
valve, start-delta typicals
1 200 % Irated
(motor
load) * %
Unsigned
Integer
20
26 16 bit Timer1 Maximum switch time (contactor feedback)
allowed
1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
27 16 bit Timer2 Motor start time 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
28 16 bit Timer3 Modbus Bus failure OFF/ON delay time 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
29 16 bit Timer4 Maximum switch time (current flow) 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
30 16 bit Timer5 Minimum switch over time 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
31 16 bit Timer6 Profibus Class 1 Bus failure OFF/ON delay time 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
32 16 bit Timer7 Blocked motor time/Overload/Locked Rotor/
Stalled Rotator 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
33 16 bit Timer8 Maximum Star time 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
34 16 bit Timer9 Star / Delta Switch over time 1 65535 1 msec Setting *
10msec
Unsigned
Integer
1
35 16 bit Timer10 Maximum switch time limit switch 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
36 16 bit Timer11 Maximum soft starter time 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
37 16 bit Timer12 Maximum soft stop time/ max breaker ON 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
38 16 bit Timer13 Applicable to custom logic only 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
39 16 bit Timer14 Applicable to custom logic only 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
40 16 bit Timer15 Undercurrent delay 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
41 16 bit Timer16 Start Attempt 1 65535 1 msec Setting *
100 msec
Unsigned
Integer
1
42 16 bit Count1 (Not used in EntelliPro ES retrofit
version) Applicable to custom logic only 1 65535 1 Unsigned
Integer
1
43 16 bit Count2 (Not used in EntelliPro ES retrofit
version) Applicable to custom logic only 1 65535 1 Unsigned
Integer
1
44 16 bit Count3 (Start Attempt Counter in V5) Number of start attempts allowed within a
specified time interval set by timer16
Example:
Timer16 is set 10 secs -
Count3 = 3
3 starts are allowed in 10 seconds interval
1 40 1 Unsigned
Integer
10