Metrohm 751 GPD Titrino - Manual (Page 123)

3.2. Remote control commands
751 GPD Titrino
120
*Parameter Tree part "Parameters for SET"
Ã
. SET1 Control parameters for EP1
³ Ã .EP Endpoint 1 depends on meas.quant. 3.2.2.29.
³ Ã .UnitEp Unit of endpoint read only ditto
³ Ã .Dyn Dynamics depends on meas.quant. 3.2.2.30.
³ Ã .UnitDyn Unit of dynamics read only ditto
³ Ã .MaxRate Maximum dosing rate 0.01...10...150, max. ditto
³ Ã .MinRate Minimum dosing rate 0.01...25.0...9999 ditto
³ Ã .Stop Titration stop
³ ³ Ã .Type Type of stop criterion drift, time 3.2.2.31.
³ ³ Ã .Drift Stop drift 1...20...999 ditto
³ ³ Ã .Time Switch-off delay time 0...10...999, inf ditto
³ ³ Ã .StopT Stop time 0...999 999, OFF ditto
à . SET2 Control parameters for EP2, as for EP1
Ã
. TitrPara Titration parameters
³ Ã .Direction Titration direction +, -, auto 3.2.2.32.
³ Ã .XPause Waiting time before start volume 0...999 999 3.2.2.33.
³ Ã .Start V Start volume
³ ³ Ã .Type Type of start volume abs., rel., OFF 3.2.2.15.
³ ³ Ã .V Volume for absolute start volume 0...999.99 ditto
³ ³ Ã .Factor Factor for relative start volume 0... ± 999 999 ditto
³ ³ Ã .Rate Dispensing rate for start volume 0.01...150.0, max. ditto
³ Ã .Pause Waiting time after start volume 0...999 999 3.2.2.16.
³ Ã .ExtrT Extraction time 0...999 999 3.2.2.34.
³ Ã .DosUnit Selection of the dosing unit internal D0, external D1,
³ ³ external D2 3.2.2.17.
³ Ã .MeasInput Measuring input 1, 2, diff. 3.2.2.18.
³ Ã .Ipol Polarization current 0...1... ± 127 ditto
³ Ã .Upol Polarization voltage 0...400... ± 1270 ditto
³ Ã .PolElectrTest Test for polarized electrodes ON, OFF ditto
³ Ã .Temp Titration temperature -170.0...25.0...500.0 3.2.2.19.
³ Ã .TDelta Time interv. for meas.acquisition 1...2...999 999 3.2.2.35.
³
à . StopCond Stop conditions
³ Ã .VStopStop volume
³ ³ Ã .Type Type of stop volume abs., rel., OFF 3.2.2.20.
³ ³ Ã .V Volume for absolute stop volume 0...99.99...9999.99 ditto
³ ³ Ã .Factor Factor for relative stop volume 0... ± 999 999 ditto
³ Ã .FillRate Filling rate 0.01...150.0, max. 3.2.2.23.
³
à . StatisticsStatistics
³ Ã .Status Status of statistics calculation ON, OFF 3.2.2.24.
³ Ã .MeanN No. of individual determinations 2...20 ditto
³ Ã .ResTab Result table
³ ³ Ã .Select original,delete n,delete all ditto
³ ³ Ã .DelN Deletion of individual results 1...20 ditto
³
à . Presel Preselections
³ Ã .Cond Conditioning ON, OFF 3.2.2.36.
³ Ã .DriftDisp Display of drift during cond. ON, OFF ditto
³ Ã .DCor Drift correction
³ ³ Ã .Type Type of drift acquisition auto, man., OFF ditto
³ ³ Ã .Value Drift value for manual drift corr. 0.0...99.9 ditto
³ Ã .IReq Request of Id's after start id1, id1&2, all, OFF 3.2.2.26.
³ Ã .SReq Request of smpl size after start value, unit, all, OFF ditto
³ Ã .LimSmplSize Limits for sample size 3.2.2.27
³ ³ Ã .Status Status of limit control ON, OFF ditto
³ ³ Ã .LoLim Lower limit 0.0...999 999 ditto
³ ³ Ã .UpLim Upper limit 0.0...999 999 ditto
³ Ã .ActPulse Output of a pulse first, all, cond., OFF 3.2.2.28.