Metrohm 751 GPD Titrino User Manual
Page 180
3.2 Remote control commands
751 GPD Titrino
177
Selection of the values from the titrator which are sent in the set time interval
(see 3.2.2.165, formats see 3.2.2.144):
.CyclNo:
Cycle number. Together with the cycle time (3.2.2.149), a time
frame can be set up. The other data belong to the corresponding
cycle number. The cycle number is set to 0 at the start of a method
and it is incremented until the end of the method.
.V:
Volume.
.Meas:
Measuring value with STAT, DOS, DOC with activated measured
value monitoring
.dVdt:
associated volume drift.
.dMeasdt: associated measured value drift.
.dMeasdV: associated 1st derivative of the titration curve.
.ERC:
ERC in DET.
.T:
In STAT, DOS, DOC, with activated temperature monitoring.
The unit "titrator" must be preset (see 3.2.2.166).
3.2.2.
3.2.2.169.
169. Se
Setup.A
.AutoInfo.S
.Status
ON
ON, OFF
Se
Setup.A
.AutoInfo.P
.P
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.R
.T.R
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.G
.T.G
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.GC
.T.GC
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.S
.T.S
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.B
.T.B
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.F
.T.F
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.E
.T.E
ON, OFF
OFF
Se
Setup.AAutoInfo.T.H
.T.H
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.C
.T.C
ON, OFF
OFF
Se
Setup.AAutoInfo.T.O
.T.O
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.N
.T.N
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.Re
.T.Re
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.Si
.T.Si
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.M
.T.M
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.EP
.T.EP
ON, OFF
OFF
Se
Setup.A
.AutoInfo.T.RC
.T.RC
ON, OFF
OFF
Se
Setup.A
.AutoInfo.C.B
.C.B1
ON, OFF
OFF
Se
Setup.A
.AutoInfo.C.R
.C.R1
ON, OFF
OFF
Se
Setup.A
.AutoInfo.C.B2
.C.B2
ON, OFF
OFF
Se
Setup.A
.AutoInfo.C.R2
.C.R2
ON, OFF
OFF
Se
Setup.A
.AutoInfo.I.I
ON, OFF
OFF
Se
Setup.A
.AutoInfo.O
.O
ON, OFF
OFF
ON means that the Titrino reports automatically the moment the corresponding
change occurs.
.Status:
Global switch for all set AutoInfo.
.P
PowerOn: Simulation of power on (3.2.2.171). Not from mains.
Messages from node .T, Titrator:
.T.R
Ready: Status 'Ready' has been reached.
.T.G
Go: Instrument has been started.
.T.GC
GoCommand: Instrument (or submethod in TIP) has received a go
command.
.T.S
Stop: Status 'Stop' has been reached.