Metrohm 746 VA Trace Analyzer - Manual (Page 524)

7.3 Error messages
746 VA Trace Analyzer / 747 VA Stand
7-25
Error message Meaning/Causes Rectification Exit
SEGM.<segm> - ERROR 5:
Instruction not allowed
in block: line ## There is an inadmissible
instruction in the specified
program line
Delete inadmissible instruction in the
segment <segm>
Esc
SEGM.<segm> - ERROR 6:
Missing part of prep.
(PREP, PREP), >PREP One of the three instructions for
a PREP block missing
In program in the segment <segm> ,
check that all three instructions (PREP ,
PREP) and >PREP are present
Esc
SEGM.<segm> - ERROR 8:
Invalid with VARNI:
line ## Inadmissible parameter for
parameter variation
Check parameter name for
Param.name in the segment <segm>
and correct
Esc
SEGM.<segm> - ERROR 9:
Invalid with (CSWEEP:
line ## Inadmissible instruction in the
CSWEEP block (only RAMP is
allowed)
Delete inadmissible instruction in the
CSWEEP block in the segment <segm>
Esc
SEGM.<segm> - ERROR 10:
Inconsist. value in
.....: line ## Inadmissible value for the
specified parameter
Change parameter value in the segment
<segm>
Esc
SEGM.<segm> - ERROR 11:
Value inconsist. with
electrode: t.step in
line ## t.step value for specified
electrode too low
− Increase t.step or reduce t.modul
− Change electrode type
Esc
SEGM.<segm> - ERROR 12:
Missing value in line
## Missing parameter value in the
specified program line
Entry parameter value in the segment
<segm>
Esc
SEGM.<segm> - ERROR 13:
Not allowed data-
generating: line ## Inadmissible data-generating
instruction in the specified
program line
Delete inadmissible instruction in the
segment <segm>
Esc
SEGM.<segm> - ERROR 14:
Not allowed in segment:
line ## Inadmissible instruction in the
segment
Delete inadmissible instruction in the
segment <segm>
Esc
SEGM.<segm> - ERROR 16:
Incorrect use of (CAL
... RINSE sequence If several CAL loops are used in
a program, every loop must
have a RINSE instruction
Enter RINSE instructions in the seg-
ment <segm>
Esc
SEGM.<segm> - ERROR 17:
Sweep range too small Sweep range too small
(< 8 measured values)
Increase sweep range or decrease
U.step or t.step
Esc
SEGM.<segm> - ERROR 18:
Sweep range too large Sweep range too large
(> 1000 measured values)
Decrease sweep range or increase
U.step or t.step
Esc
SEGM.<segm> - ERROR 19:
Missing t.step t.step value missing or is
<1 ms (possible only in
variation loops)
Enter variation loop for t.step in the
segment <segm> so that t.step
remains >1 ms
Esc
SEGM.<segm> - ERROR 20:
Conditioning cycle
range too small Initial voltage U.start and
final voltage U.end of the
CONDC instruction are identical
Change U.start and/or U.end in the
CONDC instruction
Esc
SOLUTIONS - ERROR 1:
Mass conc. conflict on
line ## The mass concentrations of
solutions with the same name
do not match
Check mass concentrations Mass
conc. of the solutions on the
”SOLUTIONS”, ”OP.SEQUENCE”,
”SEGMENTS” and ”SUBSTANCES/
Calibration” page and change
Esc
STORAGE - ERROR 1:
Destination file
secured Secured file can not be deleted
or overwritten
Unsecure file before deleting or over-
writing with <Secure/Unsecure>
E/C
STORAGE - ERROR 2:
Can not find source The file to be copied is not
available at the source speci-
fied
Check source (working storage or
RS232 interfaces) to see whether the file
to be copied exists
E/C
STORAGE - ERROR 3:
Entry table full Maximum number of files (256)
reached
Delete old files E/C