Document Outline

• 5000-6.2.10, Pyramid Integrator, Installation Manual
• Important User Information
• Summary of Changes
  • Additional Information
• Table of Contents
• Preface - Using This Manual
  • Manual Objectives
  • Pyramid Integrator Documentation
  • Who Should Use this Manual
  • Related Publications
  • Terms and Conventions
• 1 - Preparing for Installation
  • Chapter Objectives
  • To Prepare for Installation
  • Gather the Documentation
  • Hardware Availability
  • Unpack the Hardware
  • Identify the Hardware
  • Module Weights
  • What to do Next
• 2 - Mounting the Components
  • Chapter Objectives
  • To Mount the System Components
  • Gather the Mounting Documentation
  • Gather the PI Components
  • Gather the Tools and Supplies
  • Rack Mount the Components
  • Panel Mount the Components
  • Mount the Fan Assembly
  • Mount the Camera
  • Mounting a Black and White Monitor (2801-N6, -N9, -N20)
  • Mounting the I/O Board 1771-JMB
  • What to do Next
• 3 - Grounding the Components
  • Chapter Objectives
  • To Ground the Components
  • Gather the Grounding Documentation
  • Gather the Necessary Tools and Supplies
  • Ground the Components
  • What to do Next
• 4 - Installing the Modules
  • Chapter Objectives
  • How to Use this Chapter
  • Help to Prevent Electrostatic Damage
  • Lithium Battery Information
  • Gather the Module Documentation
  • Power Supply
  • RM/KA Module
  • RS Module
  • LP Module
  • Vision Processor Modules
  • MicroVAX Information Processors
  • EI Module
  • OSI Carrierband/Broadband Interface Module
  • Configuring the PI OSI Interface Module
  • OSI Interface
• 5 - Installation the Peripherals
  • Chapter Objectives
  • Where to Begin
  • Install a Programming Terminal
  • Install the Industrial Disk
  • Install the 4 Port Distribution Panel
  • Install the Program Loader
  • What to do Next
• 6 - Installing the Vision Components
  • Chapter Objectives
  • Installing the Vision System
  • Before You Begin
  • Connect the I/O Interface Box
  • Connect the User Interface Box
  • Connect the Camera to the CVIM Module
  • Connect the I/O Board
  • Connect to Remote I/O Link
  • What to do Next
• 7 - Installing 1771 I/O
  • Chapter Objectives
  • What You Should Have Completed
  • Before You Begin
  • Set I/O Chassis Switches
  • Set the I/O Chassis Configuration Jumper
  • Set I/O Adapter Module Switches
  • Configure the Extemded-Local I/O Adapter Module
  • Set 1771-AM1, -AM2 I/O Chassis/Adapter Switches
  • Install Keying Bands
  • Installing and Wiring I/O Modules
  • Connecting Shielded Cables
  • Connecting I/O Power Supplies
  • What to do Next
• 8 - Installing Non-standard I/O
  • Chapter Objectives
  • Setting Direct Communication Module Switches
  • Setting PLC Interface Module Switches
  • Setting 1785 PLC-5 Processor Switches
  • Setting RediPANEL Push-button Module Switches
  • Setting RediPANEL Keypad Module Switches
  • What to do Next
• 9 - Connecting the I/O Link
  • Chapter Objectives
  • Connecting the Remote I/O Link
  • Connecting the Extended-Local I/O Link On the RS5 Modules
  • Connecting to a 1771-AM1, -AM2 I/O Chassis with Integral Power Supply and Adapter
  • Connecting to a 1785 PLC-5 Controller
  • Connecting to a Direct Communication Module
  • Connecting to a RediPANEL Module
  • Connecting to a PLC Interface Module
  • Connecting to a PanelView Operator Terminal
  • What to do Next
• 10 - Connecting ac Power
  • Chapter Objectives
  • What You Will Be Doing
  • Disable Inputs and Outputs
  • Power Supply
  • Industrial Disk
  • Fan Assembly
  • Connecting I/O Power Supplies
• 11 - Checking the Hardware
  • Chapter Objectives
  • Checking the Hardware
  • Disable All Inputs and Outputs
  • Perform Standalone Hardware Check
  • Check the PI Modules
  • Check I/O
  • Check Vision Components
  • Check Peripherals
  • What to do Next
• 12 - Configuring Hardware for the MicroVAX Information Processors EP and EE
  • Chapter Objectives
  • Gather Your Equipment
  • Start Up and Test MicroVAX Information Processor Hardware
  • Verify and Format Disk (for 5730-CPU1)
  • Formatting the Industrial Disk (for 5731-CPU1, -CPU2)
  • Set Hardware Defaults
  • What to do Next
• A - Installing and Removing a Module
  • What's in this Appendix
  • Changing a Memory Module
  • Installing a PI Module in the Chassis
  • Removing a PI Module from the Chassis
  • Installing Filler Plates
  • How to Wire a Connector
• B - Mounting Dimensions
  • What's in this Appendix
• C - Cable Connections for the Resource Manager and KA Module
  • What's in this Appendix
  • Switch Settings
  • Cable Connections
  • Cable Pinouts
• D - Start Up and Configure the Modules
  • What's in this Appendix
• Index
• Back Cover