Document Outline

• 1758-UM002D-EN-P DataSite Electronic Flow Meter and Remote Terminal Unit User Manual
  • Important User Information
  • Preface
    • Who Should Use this Manual
    • Purpose of this Manual
    • Related Documentation
    • Common Techniques Used in this Manual
    • Table of Contents
  • Chapter 1
    • DataSite Configuration Settings Utility (DS Settings)
    • Introduction
    • Hardware and Software Requirements
    • Start DS Settings
      • Create a New Project
      • Save a Project
      • Open a Project
      • Close DS Settings
    • Configure PC Communication Settings
    • Configure Controller Communication Settings
      • Configure Serial Port Settings
      • Configure TCP/IP Settings
      • Register IP Settings
      • Lower the Power Consumption
      • Display the Default Settings
      • Save the Controller Communication Settings
      • Load the Controller Communication Settings
      • Upload the Controller Communication Settings from the Controller
      • Download the Controller Communication Settings to the Controller
      • Display the Device Information
      • Close the Controller Communication Settings dialog box
    • Settings
      • Understand the Scan Blocks
      • Open the Scan Settings Dialog Box
      • Edit a Scan Block
      • Insert a Scan Block
      • Delete a Scan Block
      • Copy a Scan Block
      • Paste a Scan Block
      • Paste a Scan Block to Multiple Rows
      • Use the Shortcut Menu
      • Load the Scan Settings
      • Save the Scan Settings
      • Upload the Scan Settings from the Controller
      • Download the Scan Settings to the Controller
      • Clear the Error Count
      • Close the Scan Settings Dialog Box
    • Configuration Example
    • Configure HART Settings
      • Open the HART Settings Dialog Box
      • Understand HART Commands
      • Insert a HART Scan Block
      • Edit a HART Scan Block
      • Delete a HART Scan Block
      • Copy a HART Scan Block
      • Paste a HART Scan Block
      • Paste a HART Scan Block to Multiple Rows
      • Use the Shortcut Menu
      • Load the HART Settings
      • Save the HART Settings
      • Upload the HART Settings from the Controller
      • Download the HART Settings to the Controller
      • Clear the Error Count
      • Close the HART Settings Dialog Box
    • Configure Event Settings
      • Event Examples
      • Configure a System Event
      • Configure an Alarm Event
      • Configure a Calendar Event
      • Configure a Time Event
      • Upload Event Settings from the Controller
      • Download Event Settings from the Controller
      • Save the Event Settings
      • Load the Event Settings
      • Close the Event Settings Dialog Box
    • Debug the Controller Programs
      • Open the Controller Debug Dialog Box
      • Toggle between Online and Offline Debugging
      • Set the Scan Time for the Online Debugging Mode
      • Add a Register Group
      • Delete a Register Group
      • Rename a Register Group
      • Add Registers
      • Edit a Register
      • Delete a Register
      • Read the Controller-Run Parameters
      • Clear Error Codes
      • Adjust the System Time
      • Close the Controller Debug Dialog Box
    • Initialize the Controller
      • Open the Controller Initialize Dialog Box
      • Switch Controller into Service Mode
      • Initialize DataSite Workbench
      • Reset the Controller Communication Parameters
      • Reset the Register Values
      • Reset the DNP3 Parameters
      • Test the Communication
      • Initialize the File System
      • Display System Information
      • Clear the Status Messages
    • Allocate Registers
      • Read and Write Registers
      • Modbus Register for Signals
  • Chapter 2
    • DataSite Flow Configuration Utility (DS FloConfig)
    • Introduction
    • Hardware and Software Requirements
    • Start DS FloConfig
      • Create a New Project File
      • Open a Project File
      • Open a Recent Project File
      • Close DS FloConfig
    • Configure PC Communication Settings
      • Open the PC Communication Dialog Box
      • Set Up PC Communication
    • Configure FLO Communication Settings
      • Open the FLO Communication Dialog Box
      • Configure Serial Port Settings
      • Configure TCP/IP Settings
      • Lower Power Consumption
      • Set the Resource Number (Optional)
      • Change the Communication Password
    • Configure FLO RTC Settings
      • Open the FLO RTC Dialog Box
      • Read the Real-Time Clock
      • Calibrate the Real-Time Clock (RTC)
      • Set the Contract Time
    • Record Flow Results for a Meter Run
      • Display the Flow Results of a Meter Run
      • Perform a Flow Calculation Test
      • Display the Field Parameters of a Meter Run
      • Select the Measurement System
      • Enable a Meter Channel and Its Accumulation Calculation
      • Set the Flow Rate Calculation Interval
      • Select the Gas Flow Calculation Standard (AGA3/AGA7)
      • Configure AGA3 Process Parameters
      • Configure AGA7 Process Parameters
      • Configure Field Signal Parameters for the AGA3 Standard
      • Configure Field Signal Parameters for the AGA7 Standard
      • Select an AGA8 Method
      • Acquire the Gas Component Parameter values
    • Configure the Historical Records
      • Configure the Daily Historical Records
      • Configure the Hourly Historical Records
      • Load the Configuration from the PC
      • Save the Configuration to the PC
      • Upload the Configuration from the Controller
      • Download the Configuration to the Controller
    • View Historical Records
      • Sort Historical Records
    • Configure Alarm Events
      • Open the Alarm Config dialog box
      • Enable an Alarm Configuration
      • Insert an Alarm Configuration
      • Disable an Alarm Configuration
      • Delete an Alarm Configuration
      • Load Alarm Configurations
      • Save Alarm Configurations
      • Upload Alarm Configurations
      • Download Alarm Configurations
    • View Alarm Event Records
      • Sort Alarm Event Records
      • Understand the Alarm Record Format
    • View Event Records
      • Sort Event Records
      • Understand the Event Record Format
    • Calibrate the Meter Sensor
      • Open the Force Signals dialog box
      • Set Forced Values for Field Signals
      • Calibrate the Sensors
      • Complete the Calibration
    • Initialize the Controller
      • Open the Controller Initialization dialog box
      • Switch Controller into Service Mode
      • Reset the Communication Parameters
      • Reset the Register Values
      • Reset the AGA Flow Parameters
      • Rebuild the AGA Files
      • Delete the DataSite Workbench Program
      • Clear the DNP3 Parameters
      • Initialize the File System
      • Display System Information
      • Clear Status Message
    • Configure the Scan Settings
      • Understand the Scan Blocks
      • Open the Scan Settings Dialog Box
      • Edit a Scan Block
      • Insert a Scan Block
      • Delete a Scan Block
      • Copy a Scan Block
      • Paste a Scan Block
      • Paste a Scan Block to Multiple Rows
      • Use the Shortcut Menu
      • Load the Scan Settings
      • Save the Scan Settings
      • Upload the Scan Settings from the Controller
      • Download the Scan Settings to the Controller
      • Clear the Error Count
      • Close the Scan Settings Dialog Box
    • Configure HART Inputs
      • Open the HART Dialog Box
      • Understand HART Commands
      • Insert a HART Scan Block
      • Edit a HART Scan Block
      • Delete a HART Scan Block
      • Copy a HART Scan Block
      • Paste a HART Scan Block
      • Paste a HART Scan Block to Multiple Rows
      • Use the Shortcut Menu
      • Load the HART Settings
      • Save HART Settings
      • Upload the HART Settings from the Controller
      • Download the HART Settings to the Controller
      • Clear the Error Count
  • Chapter 3
    • DataSite DNP3 Configuration Utility (DS DNP3)
    • Introduction
      • DNP3 Features
      • DNP3 Protocol Structure
      • DNP3 Data Object Library
      • DNP3 Class Objects
      • DNP3 Internal Indication (IIN) Sign
    • SDNP3
      • SDNP3 Network Structure
      • SDNP3 Data Scan Mode
      • SDNP3 Channel and Session
      • SDNP3 Data Objects
      • SDNP3 Data Points and Database
      • SDNP3 Session I/O Points
    • Start DS DNP3
    • Configure PC Communication Settings
      • Configure the PC Communication
    • Configure DS DNP3
      • Configure the DS DNP3 Database
      • Configure a DS DNP3 Channel
      • Download the Configuration file
      • Upload the Configuration file
      • Save the Configuration file
    • Operation and Data Validation Example
      • Example
  • Chapter 4
    • Extension Modbus Protocol for DataSite Controllers (1758-FLO)
    • Modbus Register Definition
      • Modbus Register Range
      • Modbus Registers for Physical I/O Hardware
      • Modbus Registers used by the 1758-FLO Controllers
      • Modbus Registers for Contract Time
      • Modbus Registers for the Power Shutdown Time
      • Modbus Registers for Reading Gas Component Parameters
    • Addresses Associated with the Extension Modbus Protocol Commands
      • Pass Code for User
      • Command List
      • Command Number 1: Correct the System Time
      • Command Number 2: Set the Pass Code
      • Command Number 3: Set the Device Name
      • Command Number 4: Read the Device Name
      • Command Number 5: Disable/Enable the Flow Calculation
      • Command Number 6: Read the Disable/Enable Flow Calculation Setting
      • Command Number 7: Set the Transaction (Contract) Time
      • Command Number 8: Read the Transaction (Contract) Time
      • Command Number 9: Set Up the Input Signal Test
      • Command Number 10: Read the Input Signal Test
      • Command Number 11: Disable/Enable the Accumulation Calculation
      • Command Number 12: Read Disable/Enable Setting for Accumulation Calculation
      • Command Number 13: Set the Input Parameters
      • Command Number 14: Read the Input Parameters
      • Command Number 15: Set the Alarm Range of Input Parameters
      • Command Number 16: Read the Alarm Range of Input Parameters
      • Command Number 17: Set Up the Calculation Input Parameters
      • Command Number 18: Read the Calculation Input Parameter
      • Command Number 19: Set Up the Gas Component Parameter
      • Command Number 20: Read the Gas Component Parameter
      • Command Number 21: Reset Accumulation
      • Command Number 22: Get Daily History
      • Command Number 23: Get Hourly History
      • Command Number 24: Read Alarm Logs
      • Command Number 25: Read New Alarm Logs
      • Command Number 26: Read Event Logs
      • Command Number 27: Read New Event Logs
      • Command Number 28: Disable/Enable the Automatic Components Analysis Instrument
      • Command Number 29: Read the Flag of Getting Gas Component Parameters from the Gas Component Analyzer
      • Command Number 30: Acknowledge Alarms
      • Command Number 31: Acknowledge Events
  • Chapter 5
    • Enron Modbus Protocol for the 1758-FLO DataSite Controller
    • Register Addresses
    • 1758-FLO DataSite Variables
    • Information Variables
      • Short Integer Variables
      • Long Integer Variables
      • Floating Point Variables
      • Hourly and Daily History
      • Event and Alarm Logs
  • Chapter 6
    • Global Event Codes for Modbus Protocols
    • Global Event Codes
• Back Cover