IAI America XSEL-KE - Manual (Page 186)

171
Part 4 Commands
z CHVL (Change speed)
Command, declaration
Extension condition
(LD, A, O, AB, OB)
Input condition
(I/O, flag)
Command,
declaration
Operand 1 Operand 2
Output
(Output, flag)
Optional Optional CHVL Axis pattern Speed CP
[Function] Change the speed of the axes operating in other task.
When a CHVL command is executed, the speed of the axes specified in operand 1 will change to
the value specified in operand 2.
(Note 1) This command is not valid on an axis operated by a CIR, ARC, PSPL, PUSH, ARCH, PACH, CIRS
or ARCS command.
(Note 2) Executing a CHVL command for an axis operating in sigmoid motion (SCRV command) will
JHQHUDWHDQ³(UURU1R&&6SHHGFKDQJHFRQGLWLRQHUURU´
1RWH  7KLVLVDWHPSRUDU\VSHHGFKDQJHFRPPDQGLVVXHGIURPRWKHUWDVNWRWKHDFWLYHSDFNHW SRLQW ,W
is not affected by the data declared by VEL.
Program 1 Program 2
VEL 300
x
x
MOVP 1
CHVL 111 100 MOVP 2
MOVP 3
x
x
The axis pattern can be specified indirectly using a variable.
When program 1 is rephrased based on indirect specification using a variable:
111 (binary)
o 7 (decimal)
LET 1 7 Assign 7 to variable 1.
CHVL *1 100
(Note 4) Since this command is valid only for the packet that is active at the time of execution of the
command for an axis subject to continuous motion in a PATH command, etc., caution must be
H[HUFLVHGDJDLQVWWKHWLPLQJVKLIW7KHSDFNHWKDQGOLQJZLOOEHSXWRQKROGGXULQJVSHHGFKDQJH
processing, so caution must also be exercised against the locus shift.
Program 1 Program 2
x VEL 300
x x
x x
CHVL 111 100 PATH 1 5
x
x
x
If CHVL is executed in program 1 while PATH is executed in program 2, or specifically during the
PATH movement from point No. 2 to point No. 3, the speed specified by CHVL (100 mm/sec in the
above example) will become valid only during the PATH movement to point No. 3. Other travel
speeds will remain at the speed specified by VEL (300 mm/sec in the above example).
(Note 5) Override of the CHVL call task will be applied, so caution must be exercised.
(Note 6) The maximum speed of the specified axis completing home return will be clamped by the minimum
YDOXHVHWLQ³$[LVVSHFLILFSDUDPHWHU1R0D[LPXPRSHUDWLQJVSHHGRIHDFKD[LV´RU³$[LV
VSHFLILFSDUDPHWHU1R0D[LPXPVSHHGOLPLWHGE\PD[LPXPPRWRUVSHHG´ZLWKUHVSHFWWRWKH
specified axis and related interpolation axes currently operating. To prevent the maximum speed
from being limited due to the effect of other axis whose maximum speed is lower than the speed
specified in the CHVL command, issue a CHVL command in multiple steps corresponding to the
respective axes having different maximum speeds. In particular, specification of a CHVL command
in a separate step is recommended for a rotating axis.
[Example] CHVL 1111 500 Ÿ CHVL 111 500
CHVL 1000 500
No. 1 No. 3 No. 5
No. 2 No. 4
VEL 100
If CHVL is executed in program 1 while MOVP 2
is executed in program 2, the travel speed of
MOVP 2 will become 100 mm/sec.
The speeds of other move commands will
remain 300 mm/sec.