Lenze 8400 BaseLine D - Manual (Page 221)

Lenze · 8400 BaseLine D · Reference manual · DMS 5.5 EN · 01/2014 · TD05
221
9 Parameter reference
9.3 Table of attributes
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
9.3 Table of attributes
The table of attributes contains information that is required for a communication to the controller
via parameters.
How to read the table of attributes:
Column Meaning Entry
Code Parameter name Cxxxxx
Name Parameter short text (display text) Text
Index dec Index under which the parameter is addressed.
The subindex of array variables corresponds to the
Lenze subcode number.
24575 - Lenze code number Is only required for access via a bus sys-
tem.
hex 5FFF
h
- Lenze code number
Data DS Data structure E Single variable
(only one parameter element)
A Array variable
(several parameter elements)
DA Number of array elements (subcodes) Number
DT Data type INTEGER_16 2 bytes with sign
INTEGER_32 4 bytes with sign
UNSIGNED_8 1 byte without sign
UNSIGNED_16 2 bytes without sign
UNSIGNED_32 4 bytes without sign
VISIBLE_STRING ASCII string
Factor Factor for data transfer via a bus system, depen-
ding on the number of decimal positions
Factor 1 ≡ no decimal positions
10 ≡ 1 decimal position
100 ≡ 2 decimal positions
1000 ≡ 3 decimal positions
Access R Read access  Reading permitted
W Write access  Writing permitted
CINH Controller inhibit required  Writing is only possible when the controller is inhibited
Code Name Index Data Access
dec hex DS DA DT Factor R W CINH
C00002 Device commands 24573 5FFD A 32 UNSIGNED_8 1  
C00003 Status of last device command 24572 5FFC E 1 UNSIGNED_8 1 
C00006 Motor control 24569 5FF9 E 1 UNSIGNED_8 1  
C00007 Control mode 24568 5FF8 E 1 UNSIGNED_16 1  
C00010 Minimum analog setpoint 24565 5FF5 A 1 INTEGER_16 100  
C00011 Appl.: Reference speed 24564 5FF4 E 1 UNSIGNED_16 1  
C00012 Accel. time - main setpoint 24563 5FF3 E 1 UNSIGNED_32 1000  
C00013 Decel. time - main setpoint 24562 5FF2 E 1 UNSIGNED_32 1000  
C00015 VFC: V/f base frequency 24560 5FF0 E 1 UNSIGNED_16 10  
C00016 VFC: Vmin boost 24559 5FEF E 1 UNSIGNED_16 100  
C00018 Switching frequency 24557 5FED E 1 UNSIGNED_8 1  
C00019 Auto-DCB: Threshold 24556 5FEC E 1 UNSIGNED_16 1  
C00021 Slip comp. 24554 5FEA E 1 INTEGER_16 100  
C00022 Imax in motor mode 24553 5FE9 E 1 UNSIGNED_16 100  
C00023 Imax in generator mode 24552 5FE8 E 1 INTEGER_16 100  
C00024 Comparison value N_Act 24551 5FE7 E 1 INTEGER_16 100  
C00026 AINx: Offset 24549 5FE5 A 1 INTEGER_16 100  
C00027 AINx: Gain 24548 5FE4 A 1 INTEGER_32 100  
C00028 AINx: Input voltage 24547 5FE3 A 1 INTEGER_16 100 
C00029 AINx: Input current 24546 5FE2 A 1 INTEGER_16 100 
C00033 AINx: Output value 24542 5FDE A 1 INTEGER_16 100 
C00034 AINx: Configuration 24541 5FDD A 1 UNSIGNED_8 1  