H3C Technologies H3C WX3000E Series Wireless Switches User Manual
H3c wx series access controllers, Wlan configuration guide
Advertising
This manual is related to the following products:
H3C WX5500E Series Access Controllers, H3C WX3500E Series Access Controllers, H3C WX2500E Series Access Controllers, H3C WX6000 Series Access Controllers, H3C WX5000 Series Access Controllers, H3C WX3000 Series Unified Switches, H3C LSWM1WCM10 Access Controller Module, H3C LSUM3WCMD0 Access Controller Module, H3C LSUM1WCME0 Access Controller Module, H3C LSWM1WCM20 Access Controller Module, H3C LSQM1WCMB0 Access Controller Module, H3C LSRM1WCM2A1 Access Controller Module, H3C LSBM1WCM2A0 Access Controller Module, H3C WA3600 Series Access Points, H3C WA2600 Series WLAN Access Points
Table of contents
Document Outline
- Title Page
- Preface
- Contents
- Configuring WLAN interfaces
- Configuring WLAN services
- WLAN service overview
- IEEE 802.11 overview
- AC-AP tunnel overview
- WLAN topologies
- Protocols and standards
- Configuring WLAN service
- Configuration task list
- Enabling WLAN service
- Configuring country code
- Configuring software automatic update
- Configuring a WLAN service template
- Configuring an AP
- Configuring auto AP
- Configuring basic network parameters for an AP
- Configuring AC-AP tunnel dual-link
- Enabling CAPWAP/LWAPP tunnel encryption with IPsec
- Configuring radio parameters
- Configuring a radio policy
- Enabling automatic creation of radio policies
- Configuring 802.11n
- Shutting down all LEDs on APs
- Displaying and maintaining WLAN service
- Configuring user isolation
- Configuring AP group for AP based access control
- Configuring SSID-based access control
- Configuring uplink detection
- Configuring AC hot backup
- WLAN service configuration examples
- WLAN service configuration example
- WLAN auto-AP configuration example
- AC-AP tunnel dual-link configuration example
- Configuration example for CAPWAP tunnel encryption with IPsec
- Example for configuring fit APs on an AC
- 802.11n configuration example
- User isolation configuration example
- Uplink detection configuration example
- AP group configuration examples
- Configuring WLAN security
- Authentication modes
- WLAN data security
- Client access authentication
- Protocols and standards
- Configuring WLAN security
- WLAN security configuration examples
- Supported combinations for ciphers
- Configuring WLAN roaming
- Configuring WLAN RRM
- Overview
- Configuration task list
- Configuring data transmit rates
- Configuring channel exclusion
- Configuring DFS
- Configuring mesh DFS
- Configuring TPC
- Configuring a radio group
- Configuring scan parameters
- Configuring power constraint
- Displaying and maintaining WLAN RRM
- Load balancing
- Configuring band navigation
- Enabling 802.11g protection
- Configuring 802.11n protection
- Configuring the maximum bandwidth
- WLAN RRM configuration examples
- Load balancing configuration examples
- Band navigation configuration example
- Configuring WLAN IDS
- Configuring WLAN IDS frame filtering
- Configuring WLAN QoS
- Overview
- Configuring WMM
- Displaying and maintaining WMM
- WMM configuration examples
- Troubleshooting
- Configuring bandwidth guaranteeing
- Configuring client rate limiting
- Configuring WLAN mesh link
- Introduction to WLAN mesh
- Introduction to WDS
- WLAN mesh/WDS configuration task list
- Configuring an MKD ID
- Configuring mesh port security
- Configuring a mesh profile
- Configuring mesh portal service
- Configuring an MP policy
- Mapping a mesh profile to the radio of an MP
- Mapping an MP policy to the radio of an MP
- Specifying a peer MAC address on the radio
- Disabling temporary link establishment
- Displaying and maintaining WLAN mesh link
- WLAN mesh configuration examples
- Troubleshooting WLAN mesh link
- Configuring WLAN sniffer
- Configuring wireless location
- Optimizing WLAN
- Rejecting wireless clients with low RSSI
- Enabling fair scheduling
- Ignoring weak signals
- Enabling 802.11n packet suppression
- Enabling traffic shaping based on link status
- Configuring the rate algorithm
- Enabling channel sharing adjustment
- Enabling channel reuse adjustment
- Disabling buffering of multicasts and broadcasts
- Enabling multi-service optimization
- Enabling AP blinking
- Enabling packet-based TPC
- Enabling the AP to trigger client re-connection
- Enabling the AP to receive all broadcasts
- Enabling the green-AP function
- Configuring a power supply mode for the AP
- WLAN optimization configuration examples
- Index