Yaskawa R1000 Series Power Regenerative Unit - Manual (Page 161)

B.2 Parameter Tables
YASKAWA ELECTRIC TOEP C710656 08B YASKAWA Power Regenerative Unit - R1000 Instruction Manual 161
Par
ame
te
r Li
st
B
8 During baseblock (N.O.) BaseBlk 1
Closed: Regenerative unit has entered the baseblock state (no
regeneration).
E Fault Fault Closed: Fault occurred.
F Through mode Not Used Set this value when using the terminal in the pass-through mode.
10 Minor fault Minor Fault Closed: An alarm has been triggered.
11 Fault reset command active Reset Cmd Active
Closed: A command has been entered to clear a fault via the input
terminals or from the serial network.
12 Timer output Timer Output Closed: Timer output.
1B During baseblock (N.C.) BaseBlk 2
Open: Regenerative unit has entered the baseblock state (no
regeneration).
1D During Regeneration Regenerating Closed: Motor is regenerating energy into the regenerative unit.
1E Restart enabled Dur Flt Restart Closed: An automatic restart is performed
20
Heatsink Overheat (oH)
pre-alarm
OH Prealarm Closed: Heatsink temperature exceeds the parameter L8-02 value.
24 Fuse Blowout Detection FUA/FUD Detect Closed: Fuse burnout detected.
25 During Run 1 During RUN 1 Closed: The drive is ready to operate.
26 During MC ON MC On Closed: The magnetic contactor is closed.
27 Overload (oL2) Warning OL2 Pre-alarm Closed: There is an overload warning.
2F Maintenance Period Maintenance
Closed: It is time to perform maintenance on the cooling fan, electrolytic
capacitor, and inrush prevention relay.
3A kWh Monitor Pulse Output Power (Produced)
Set the unit in H2-06.
Multi-function output is ON for 200 ms depending on the unit selected in
H2-06.
3B Alarm 2 Minor Fault 2
Closed: Alarm occurred (excluding Uv, AUv, Fdv, SrC, and PAUv).
Note: This setting is available in regenerative unit software versions
PRG:2003 or later.
3C LOCAL/REMOTE status Local
Open: REMOTE
Closed: LOCAL
4D oH Pre-alarm time limit OH Pre-Alarm Closed: oH pre-alarm time limit has passed.
60 Internal cooling fan alarm Fan Alrm Det Closed: Internal cooling fan alarm
100 to 160
Function 0 to 60 with inverse
output
–
Inverts the output switching of the multi-function output functions.
Set the last two digits of 1†† to reverse the output signal of that
specific function.
No.
(Address
Hex)
Name LCD Display Description Values
H3: Multi-Function Analog Inputs
H3-01
(410H)
Terminal A1 Signal
Level Selection
Term A1 Level
0: 0-10V, (LowLim=0)
1: 0-10V, (BipolRef)
0: 0 to 10 V
1: -10 to 10 V
Default: 0
Min.: 0
Max.: 1
H3-02
(434H)
Terminal A1
Function Selection
Term A1 FuncSel Sets the function of terminal A1.
Default: F
Min.: F
Max.: F
H3-03
(411H) Terminal A1 Gain
Setting
Terminal A1 Gain
Sets the level of the input value selected in H3-02 when 10
V is input at terminal A1.
Default: 100.0%
Min.: -999.9%
Max.: 999.9%
H3-04
(412H) Terminal A1 Bias
Setting
Terminal A1 Bias
Sets the level of the input value selected in H3-02 when 0
V is input at terminal A1.
Default: 0.0%
Min.: -999.9%
Max.: 999.9%
H2 Multi-Function Relay Output Settings
H2-
Setting
Function LCD Display Description
TOEP_C710656_08B_1_0.book 161 ページ ２０１５年２月５日 木曜日 午前１０時７分