Document Outline

• TTM-200ｼﾘｰｽﾞﾕｰｻﾞｰｽﾞﾏﾆｭｱﾙ 英語 48-7009-Ｄ.pdfから挿入したしおり
  • TOP
  • Contents
    • 1.1 Feature
    • 1.2 Checking the product
    • 1.3 Model table
    • 1.4 Names of parts and components
    • 1.5 Input/output function and essential functions
    • 1.6 Basic flow of setting
  • 2. Installation
    • 2.1 Precautions on installation
    • 2.2 How to install or remove the equipment
    • 2.3 Outside dimensions and panel cutting dimensions
  • 3. Wiring
    • 3.1 Precautions on wiring
    • 3.2 Terminal arrangement
    • 3.3 Wiring to each terminal
    • 3.4 Examples of wiring
  • 4. Basic operation
    • 4.1 Flow of setting mode
    • 4.2 Basic operation
  • 5. Operating the equipment
    • 5.1 Precautions on operating the equipment
    • 5.2 Operating monitor display
      • 5.2.1 Operating amount monitor: SET 04 (control setting mode)
      • 5.2.2 Timer remaining time monitor: Run mode
      • 5.2.3 Temperature measurement monitor: Run mode
      • 5.2.4 CT monitor: SET 12 (CT setting mode)
    • 5.3 How to set run settings
      • 5.3.1 Target value (SV) setting
      • 5.3.2 ON/OFF control setting
      • 5.3.3 PID control setting
      • 5.3.4 Heating/cooling PID control setting
      • 5.3.5 Indicator setting
      • 5.3.6 Excessive ascent prevention unit (alarm unit) setting
      • 5.3.7 Event setting
      • 5.3.8 How to set MD/READY
    • 5.4 How to set each function and description of function
      • 5.4.1 Auto-tuning (AT) function
      • 5.4.2 Self-tuning function
      • 5.4.3 Mode/manual function
      • 5.4.4 Bank function
      • 5.4.5 Timer function
      • 5.4.6 Loop abnormality function
      • 5.4.7 Current transformer (CT) abnormality function
      • 5.4.8 Position proportional control
      • 5.4.9 Concurrent temperature ascent function
    • 5.5 Explanation of the program run function
      • 5.5.1 Operation flow of the program run
      • 5.5.2 SET 21 program function setting
      • 5.5.3 SET 21 program function setting screen
      • 5.5.4 SET 22 program setting
      • 5.5.5 SET 22 program setting screen
      • 5.5.6 Explanation of the screen display and operation of a program run
      • 5.5.7 Complementary explanation of the program run
    • 5.6 Explanation of the bank automatic switching function
      • 5.6.1 Bank automatic switching setting
      • 5.6.2 SET 23 bank automatic switching function setting mode setting screen
      • 5.6.3 Complementary explanation of the bank automatic switching function
  • 6. Explanation on parameters
    • 6.1 Input 1 type setting
    • 6.2 Remote SV input type setting
    • 6.3 Function key function setting
    • 6.4 Control function setting
    • 6.5 Output (from OUT 1 to OUT 7) type setting
    • 6.6 Current transformer (CT) setting
    • 6.7 DI setting
    • 6.8 Timer function setting
    • 6.9 Communication function setting
    • 6.10 Initial setting
    • 6.11 Priority screen setting
    • 6.12 Bank function setting
    • 6.13 PROGRAM FUNCTION SETTING
    • 6.14 PROGRAM SETTING
    • 6.15 BANK AUTOMATIC SWITCHING FUNCTION SETTING
  • 7. Appendix
    • 7.1 Product specifications
    • 7.2 Accessories
    • 7.3 Error (abnormality) display
    • 7.4 Troubleshooting
    • 7.5 Setting list
      • 7.5.1 Run mode
      • 7.5.2 Input 1 setting mode (SET 01)
      • 7.5.3 Input 2 setting mode (SET 02)
      • 7.5.4 Key function setting mode (SET 03)
      • 7.5.5 Control setting mode (SET 04) (1/4)
      • 7.5.6 OUT 1 and 2 setting modes (SET 05 and 06) (1/3)
      • 7.5.7 OUT 3 to 7 setting modes (SET 07, 08, 09, 10 and 11) (1/2)
      • 7.5.8 CT setting mode (SET 12)
      • 7.5.9 DI setting mode (SET 13)
      • 7.5.10 Timer 1 to 3 setting modes (SET 14, 15 and 16)
      • 7.5.11 Communication setting mode (SET 17)
      • 7.5.12 Initial setting mode (SET 18)
      • 7.5.13 Priority screen setting mode (SET 19)
      • 7.5.14 Bank setting mode (SET 20)
      • 7.5.15 Program function setting mode (SET 21)
      • 7.5.16 Program setting mode (SET 22)
      • 7.5.17 Bank automatic switching function setting mode (SET 23)