Dynon Avionics SkyView System Installation Guide - Manual (Page 9)

SkyView System Installation Guide – Revision S ix
Revision Revision Date Description
ADS-B traffic (in addition to Dynon Avionics SV-XPND-261 or -262).
Updated SV-EMS-220/221 to reflect that Pin 23 is now a “Type C” input (was previously only
Pins 8, 22, and 31).
Updated SkyView display Contact #1 Input is now (Optional) AP External LEVEL Button.
Updated SL30 instructions – now able to monitor status on top bar and push frequencies.
Added SL40 wiring instructions – now able to monitor status on top bar and push frequencies.
Added recommendation in SV-NET-SERVO instructions not to route power, ground, and CWS
using unused pins on the 9-pin connectors.
Added instructions for connecting RPM for Rotax 914.
Added instructions on setting Pulses Per Revolution for Jabiru engines and Rotax 912.
Added detailed instructions for displaying status of Heated Pitot Controller on EMS.
Added explanation about priority of displaying one of two RPM signals, if two are connected.
P September 2013
Clarified power consumption for SkyView displays.
Clarified 912 iS fuel pressure measurement requirements.
Added alternate sealing washer recommendation for oil temperature sensor.
Added configuration information for new Fuel Tank Reminder feature.
Clarified SV-BAT-320 Test Procedures.
Default Climb and Descent Vertical Speeds now used in some Expert Autopilot scenarios.
Added ADS-B configuration information to 430/530/GTN connection instructions for using those
products’ TSO’d GPS position with SkyView’s transponder ADS-B Out capability.
Q March, 2014
Added SkyView v10.0, SV-D1000T, SV-AP-PANEL, and SV-KNOB-PANEL:
- SV-D1000T touch setup (Page 4-28)
- SV-AP-PANEL installation (Section 17)
- SV-KNOB-PANEL installation (Section 18)
- Added information about Transponder software update to v2.04 (Page 11-20)
- Setup for dual SV-EMS-220/221 to monitor all cylinders of a 9-cylinder radial engine (Pages 7-
29, 7-30, 7-31)
- Added setup for monitoring dual engines with dual SV-EMS-220/221 and at least two SkyView
displays (Page 7-32)
- Added Contacts Used For Landing Gear section (Page 7-56)
- Added additional color choices in EMS ranges, choices now include Blue, Cyan, Orange, Violet,
White, and Yellow. (Page 7-64)
- Added and updated serial connection details for Garmin / Apollo SL30 COM/NAV radio, Garmin
/ Apollo SL40 COM radio, Val Avionics NAV 2000 NAV radio, Icom IC-A210 COM radio, MGL
V6/V10 COM radio, and Trig TY91 COM radio (Pages 4-16 through 4-18)
- Added GPS and NAV devices can now be named with a user selectable seven character name
instead of POS x, NAV x, GPS x
- Added explanation of new ALLOW AUTO SWITCH in setup of SV-ARINC-429 (Page 12-11)
- Added explanation of software upgrade cannot proceed if previously configured SkyView
Network devices are not connected (Page 3-15 and 3-16)
Added extensive Harness Construction Notes for connecting single and dual SV-COM-C25s to an
SV-INTERCOM-2S. (Section 16)
Added procedure for adjusting 912 iS CAN fuel flow reported to SkyView Fuel Computer (Page
7-28)
Added caution not to over-torque fasteners used to mount SV-BAT-320 (Page 9-2)
Added information to display VP-X BATT VOLTS widget in EMS display (Page 11-14)
Added information on using “FTP client” to download very large terrain database files (Page 6-
3).
Added information about Rotax 914 EGT probes (Page 7-35)