Dynon Avionics SkyView System Installation Guide - Manual (Page 10)

x SkyView System Installation Guide - Revision S
Revision Revision Date Description
Added information about Rotax 914 fuel pressure sensor (Page 7-39)
Added SV-EMS-220 / 221 is required for display of VP-X information (Page 13-1)
Added that Altitude Encoder output for Garmin SL70 is supported (Page 4-15)
Added Kavlico Pressure Sensor Manufacturer Part Numbers (Appendix G)
Improved TSO / Part 23 applicability statement (cover)
Improved guidance for installation of SV-GPS-250 (Page 2-10 and Page 8-2)
Improved information about Rotax 914 air box temperature sensor (Page 7-55)
Improved guidance that SV-XPNDR-262, even after firmware update, will not meet the
requirements of the FAA 2020 ADS-B “mandate” (Section 11 - SV-XPNDR-261/262 Installation,
Configuration, and Testing)
Improved guidance that ADAHRS/EMS/SYSTEM/NMEA Serial Output must be connected to all
SkyView displays. Updated similar guidance for other devices connected via serial port, made
language consistent on all devices connected via serial port. (Pages 4-11 through 4-19)
Improved guidance for installation of External LEVEL Button (Page 10-13)
Improved guidance on monitoring Heated Pitot status (Page 15-7)
Corrected: SV-COM-C25 Sensitivity (Page 18-6)
Corrected: To use Garmin 330ES with SV-ADSB-470, setting HEX CODE procedure is required for
all software versions (Page 14-1)
R August, 2014
New products:
 SkyView firmware v11.0
 SV-COM-X83 8.33 kHz VHF COM Radio (Chapter 17 and related information)
 Video Input Adapter for SkyView (USB) (Page 15-16)
New features:
 Support for COM radios with 8.33 kHz tuning steps:
f.u.n.k.e. Avionics ATR833
Garmin GTR 225 and Garmin GNC 255
Trig Avionics TY91 and TY92
 New alert messages for:
Mismatch between SkyView BARO setting and BARO value reported from ADS-B (Page 3-12)
New installation – modules not configured (Page 4-9)
High-resolution terrain is not available for aircraft’s current location (Page 6-3)
Sensor definition files do not match between SkyView displays (Page 7-60)
Transponder HEX CODE is not set (Page 11-15)
 Wide field of view for Synthetic Vision (Page 3-12)

Vne can now be expressed as TAS as well as IAS (Page 5-8, 10-20)

MW Fly AEROPOWER engines supported in SV-EMS-221 (Page 7-1)
 AP Disconnect/CWS Switch and External LEVEL Button status is checked at boot. (Page 10-13,
10-14)

AP Disconnect/CWS Switch is checked upon entering SERVO CALIBRATION (Page 10-16)
 ADS-B traffic display enabled with non-Dynon ADS-B OUT devices (Page 14-1)
 Independent volume control for Angle of Attack (Page 15-7)
Documentation added:
 Added explanation that SkyView can be powered on during engine start (Page 2-5)
 Recommendation to install Panel Mount USB cable with each SkyView display (Page 2-6)
 Serial port connection and configuration information for Emergency Location Transmitter
(ELT) (Page 4-20)
 External Dim Control Connections (Page 4-20)
 SV-ADAHRS-200/201 must be installed level or the Slip/Skid Ball will not be centered (Page 5-
3)
 Caution about applying too much torque when installing SV-BAT-320 (Page 9-2)
 Addition of capacitor to servo to eliminate Intercom noise (Page 10-12, 10-13)
 Pin descriptions, added wiring diagram for SV-AP-PANEL Trim Controller installation (Chapter
19)