Yokogawa Data Acquisition with PID Control CX2000 - Manual (Page 174)

6-45
IM 04L31A01-17E
6
Command
YA Sets the IP address, subnet
mask, and default gateway
Syntax YA p1,p2,p3<terminator>
p1: IP address (0.0.0.0 to 255.255.255.255)
p2: Subnet mask
(0.0.0.0 to 255.255.255.255)
p3: Default gateway
(0.0.0.0 to 255.255.255.255)
Query YA?
Example Set the IP address to 192.168.111.24, subnet
mask to 255.255.255.0, and default gateway to
0.0.0.0.
YA192.168.111.24,255.255.255.0,
0.0.0.0
Description The settings specified by this command take
effect after the CX is power cycled.
YK Sets keep alive
Syntax YK p1<terminator>
p1: Enable/Disable keep alive (ON, OFF)
Query YK?
Example Disable keep alive.
YKOFF
Description The settings specified by this command take
effect after the CX is power cycled.
YN Sets the DNS
When not using the DNS
Syntax YN p1<terminator>
p1: Use/Not use the DNS (OFF)
Query YN?
Example Do not use the DNS.
YNOFF
Description The settings specified by this command take
effect after the CX is power cycled.
When using the DNS
Syntax YN p1,p2,p3,p4,p5,p6,p7<terminator>
p1: Use/Not use the DNS (ON)
p2: Address of the primary DNS server
(0.0.0.0 to 255.255.255.255)
p3: Address of the secondary DNS server
(0.0.0.0 to 255.255.255.255)
p4: Host name (up to 64 characters)
p5: Domain name (up to 64 characters)
p6: Domain suffix 1 (up to 64 characters)
p7: Domain suffix 2 (up to 64 characters)
Query YN?
Example Use the DNS server at 192.168.0.1.
YNON,192.168.0.1
Description The settings specified by this command take
effect after the CX is power cycled.
YQ Sets the communication timeout
When not using the timeout
Syntax YQ p1<terminator>
p1: Enable/Disable communication timeout
(OFF)
Query YQ?
Example Disable timeout.
YQOFF
Description The settings specified by this command take
effect after the CX is power cycled.
When using the timeout
Syntax YQ p1,p2<terminator>
p1: Enable/Disable communication timeout
(ON)
p2: Timeout time (1 to 120) [minutes]
Query YQ?
Example Enable communication timeout and set the
timeout period to 3 min.
YQON,3
Description The settings specified by this command take
effect after the CX is power cycled.
YS Sets the serial interface
Syntax YS p1,p2,p3,p4,p5,p6<terminator>
p1: Baud rate (1200, 2400, 4800, 9600, 19200,
38400)
p2: Data length (7, 8)
p3: Parity check (NONE, ODD, EVEN)
p4: Handshaking (OFF:OFF, XON:XON,
XON:RS, CS:RS)
p5: RS-422A/485 address (01 to 32)
p6: Protocol (NORMAL, MODBUS, MODBUS-
M, LADDER)
Query YS?
Example Set the baud rate to 9600, the data length to 8,
the parity check to ODD, handshaking to
OFF:OFF, the RS-422A/485 address to 02, and
the protocol to NORMAL.
YS9600,8,ODD,OFF:OFF,02,NORMAL
Description • The settings specified by this command take
effect after the CX is power cycled.
• SERIAL can be selected on models with the
serial interface option.
6.7 Basic Setting Commands (Measurement)