Yokogawa Data Acquisition with PID Control CX2000 User Manual
Page 426
Index-4
IM 04L31A01-01E
range ..................................................... 1-22, 1-61, 4-18, 7-3
rate-of-change alarm ......................................................... 7-10
ratio setting ....................................................................... 4-20
rear panel ............................................................................ 3-3
reference deviation ................................................. 1-33, 4-24
reference point .............................................. 1-16, 1-32, 4-24
reference time ................................................................... 10-9
reflash alarm ....................................................................... 7-9
registering contact inputs (BCD) ....................................... 4-48
relay .................................................................................... 7-9
relay action/behavior ......................................................... 4-14
relay contact output ........................................................... 4-12
relay hold .......................................................................... 7-10
relay hysteresis ................................................................. 1-38
relay hysteresis value and activation point ....................... 4-26
relay output ............................................................... 7-9, 10-6
relay output/number .......................................................... 4-22
REM/LOC ............................................................................ 6-4
remaining segment time .................................................... 6-17
REMOTE ................................................................... 2-7, 2-19
remote ......................................................................... 1-6, 4-3
remote input .............................................. 1-28, 1-103, 11-11
Remote/Local, switching between ...................................... 6-4
repeat ...................................................................... 6-12, 6-16
repeat action ..................................................................... 5-11
repeat end segment .......................................................... 5-11
repeat frequency ............................................................... 5-11
repeat start segment ......................................................... 5-11
replacement period ........................................................... 13-4
report channel ................................................................. 10-14
report data ..................................................... 1-83, 1-90, 1-92
report function .................................................... 1-95, App-16
report function, starting/stopping of ................................. 10-15
report types ..................................................................... 10-14
RESET .............................................................................. 6-16
reset .................................................................................. 10-9
reset mode ........................................................................ 6-19
restart mode .............................................................. 1-17, 4-2
reverse control .................................................................. 1-34
revision history ...................................................................... vii
RJC ......................................................... 1-25, 1-61, 4-3, 7-3
RSP ............................................................................. 1-2, 2-5
RSP input .................................................................. 1-6, 1-31
RSP input selection ............................................................. 4-9
RST ................................................................................... 6-16
RUN .................................................................................. 6-16
run/auto/cascade, switching between ................................. 6-2
RUN/RST .......................................................................... 6-16
run/stop operation ....................................................... 1-7, 6-1
RUN/STP ............................................................................ 6-2
S
sample rate ......................................................................... 9-3
samples, number of ........................................................ 10-11
sampling interval ............................................................. 10-11
save .................................................................................. 1-91
save data ............................................................................ 9-6
scale .......................................................................... 4-19, 7-5
scale display ON/OFF ......................................................... 8-8
scale lower/upper limit ...................................................... 4-19
scale, number of digits displayed ...................................... 8-23
scale position .................................................................... 8-21
scan interval .............................................................. 1-60, 7-2
screen image data, saving of ............................................ 9-14
scroll .................................................................................. 8-27
SEG TIME ......................................................................... 6-17
segment edit ....................................................................... 5-3
SEGMENT NO .................................................................. 6-13
segment number ..................................... 5-6, 5-8, 6-12, 6-16
segment PID group No. ...................................................... 5-7
segment setting method ...................................................... 5-3
SEGMENT TIME ............................................................... 6-13
segment time .................................................. 5-7, 6-12, 6-16
segments ............................................................................ 5-3
self diagnosis .................................................................... 4-14
self diagnosis output ................................................. 1-6, 1-28
setpoint limiter ................................................................... 1-31
settings, initialization of ..................................................... 3-14
setup data ......................................................................... 1-93
setup data, loading and saving of ....................................... 9-9
setup mode ......................................................................... 3-4
shunt resistor ............................................................ 4-19, 7-3
shutdown function ................................................... 1-34, 4-26
single-loop control ............................................. 1-3, 1-17, 4-2
snapshot ......................................................................... 11-13
soft keys .............................................................................. 3-2
SP ............................... 1-2, 1-3, 1-30, 1-38, 4-26, 6-3, 6-11
SP, changing of ................................................................... 6-2
SP high-limit ...................................................................... 1-39
SP low-limit ....................................................................... 1-39
SP NO. .............................................................................. 6-11
SP number ........................................................................ 4-22
SP number selection source ............................................... 4-9
SP ramp-down-rate/SP ramp-up-rate ............................... 4-24
SP ramp-up-rate/SP ramp-down-rate ............................... 1-31
span ...................................................... 1-22, 1-61, 4-18, 7-4
span upper/lower limit ....................................................... 10-3
specifying the program pattern using BCD ....................... 4-47
split window display .......................................................... 6-20
square-root computation ......................................... 1-24, 4-19
ST SEG ............................................................................. 6-14
standard PID control ........................................................... 1-4
standard signal .................................................................. 1-22
standby ............................................................................. 4-22
start code ............................................................................ 5-5
start segment number ....................................................... 6-12
start/stop ......................................................................... 11-12
START/STOP key ....................................................... 3-2, 3-7
storage function ................................................................ 1-89
style number ........................................................................... i
SUFFIX ................................................................................. iv
sum scale ............................................................ 10-10, 10-14
switching condition .................................................... 1-18, 4-3
switching hysteresis ................................................ 1-32, 4-24
switching pattern number .................................................. 6-18
system information display .................................. 1-101, 11-10
T
tag/channel ......................................................................... 8-6
tag/tag comment ............................................................... 4-24
tags ................................................................. 1-73, 8-6, 10-3
target setpoint ........................................................... 5-7, 6-17
target setpoint selection method ............................... 1-4, 1-16
target setpoint tracking ...................................................... 1-30
ten-segment linearizer approximation ............................... 1-23
ten-segment linearizer biasing .......................................... 1-23
ten-segment linearizer I/O ................................................. 4-30
ten-segment linearizer mode ............................................ 4-30
time ......................................................................... 9-5, 10-14
time adjustment ............................................................... 11-12
time, setting of ................................................................... 3-11
time zone, changing of ...................................................... 3-16
TimeEvent ........................................................................... 5-8
timer number ................................................................... 10-10
Index