Par 1155 – Rockwell Automation 20D PowerFlex 700S AC Drives with Phase II Control Programming Manual User Manual
Page 129
Rockwell Automation Publication 20D-PM001C-EN-P - July 2013
129
Programming and Parameters
Chapter 2
1150
DInt2Real2 In
Input value for a second DInt to Real value conversion.
Note: This parameter was added for firmware version 3.001.
Default:
Min/Max:
0
-/+2147483648.0
Y
RW 32-bit
Integer
1151
DInt2Real2 Scale
Input value to scale the second conversion from DInt to Real. This is a multiplication to the input value after
conversion to a Real value.
Note: This parameter was added for firmware version 3.001.
Default:
Min/Max:
0.0
-/+2200000000.0
Y
RW Real
1152
DInt2Real2Result
This is the resultant output of the second conversion form a DInt value to a Real value after scaling.
Note: This parameter was added for firmware version 3.001.
Default:
Min/Max:
0.0
-/+2200000000.0
RO Real
1155
Heidn VM Pos Ref
Virtual Master position reference for the Heidenhain option card. This value is used by the Virtual Master function
as a position reference. This parameter can be linked to a position reference source, such as
[VirtEncPositFast].
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
0.0
-/+2147483648.0
Y
RW 32-bit
Integer
1156
Heidn VM Enc PPR
Virtual Master Encoder Pulse per Revolution (PPR). This value defines the encoder PPR for the Virtual Master
function. The Heidenhain option card produces the encoder pulse according to this PPR value, which is limited to
1024 or 2048 encoder lines.
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
Units:
1024
1024 and 2048 only
PPR
RW 32-bit
Integer
1160
VirtEncPositFast
Virtual Encoder position output in Task 1. One of three outputs from the Virtual Encoder function. This value is the
encoder position reference output for Task1 (fast rate).
[Virt Encdr Posit] and
[Virt Encdr Dlyed] are
the encoder position output in Task 2. For the Virtual Master Encoder function, you must use Par 1160
[VirEncPosiFast] as the position reference updated in Task 1.
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
0.0
-/+2147483648.0
RO 32-bit
Integer
1161
EGR Config
Configuration for the Electrical Gear Ratio (EGR) user function. Setting bit 7 “EGR” of
[UserFunct Enable] enables the EGR user function. The combination of bit 0 “Output Sel 0” and bit 1
“Output Sel 1” determines the output of the EGR user function as follows:
Note: This parameter was added for firmware version 4.001.
1162
EGR Mul
Multiplier (numerator) of the EGR user function position input.
(
[EGR Pos Input] x Par 1162 [EGR Mul]) /
Par 1163
[EGR Div] =
[EGR Pos Output]
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
1.0
-/+2000000.0
Y
RW 32-bit
Integer
1163
EGR Div
Divisor (denominator) of the EGR user function position input.
(
[EGR Pos Input] x
[EGR Mul]) / Par 1163 [EGR Div] =
[EGR Pos Output]
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
1.0
+1.0/+2000000.0
Y
RW 32-bit
Integer
1164
EGR Pos Input
Position reference input to the Electrical Gear Ratio user function. This parameter can be linked to a position
reference source, such as
[VirtEncPositFast].
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
0.0
-/+2147483648.0
Y
RW 32-bit
Integer
1165
EGR Pos Output
Position reference output from the Electrical Gear Ratio user function. This parameter can be linked to a position
reference sink, such as
[Heidn VM Pos Ref].
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
0.0
-/+2147483648.0
RO 32-bit
Integer
1166
EGR Pos Preset
A preset value for the Electrical Gear Ratio user function. This value is set to the value in
[EGR Pos
Output] when bits 0 “Output Sel 0” and 1 “Output Sel 1” of
[EGR Config] are set.
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
0.0
-/+2147483648.0
Y
RW 32-bit
Integer
1170
MC Generic 1
For Future Use.
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
0
+/-32767
RW 16-bit
Integer
No.
Name
Description
Values
Link
able
Re
ad
-Write
Da
ta
T
yp
e
Bit 1
Bit 0
Description
0
0
[EGR Pos Output] is set to zero
0
1
Par 1165 [EGR Pos Output] is active
1
0
Par 1165 [EGR Pos Output] is set to the value of
[EGR Pos Input]
1
1
Par 1165 [EGR Pos Output] is set to the value of
[EGR Pos preset]
Options
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Ou
tp
ut
S
el
1
Ou
tp
ut
S
el
0
Default
x
x
x
x
x
x
x
x
x
x
x
x
x
x
0
0
Bit
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
0 = False
1 = True