Hitachi SJ700-2 - Manual (Page 283)

Index
Index - 3
O
O ................................................................2-7, 2-21
O2 .................................................... 2-7, 2-21, 4-12
O2Dc.................................................................4-71
OD ...........................................................4-28, 4-29
Odc ...................................................................4-71
offline auto-tuning .............................................4-82
OHF ..................................................................4-68
OI ...............................................................2-7, 2-21
OIDc..................................................................4-71
OL, OL2 ............................................................4-40
OLR ..................................................................4-39
online auto-tuning .............................................4-84
ONT ..................................................................4-64
OPE ................................................... 3-3, 4-8, 4-51
operating methodsS............................................3-1
operation after option error ...............................4-77
operation frequency ..........................................4-14
operation mode .................................................4-33
operation time over signal
(RNT)/plug-in time over signal
(ONT) .................................................4-59, 4-63
operator ...................................................4-14, 4-65
ORG................................................................4-109
ORL ................................................................4-109
ORT ..................................................... 4-104, 4-110
OTQ ..................................................................4-65
output current monitoring ....................................4-1
output frequency monitoring ...............................4-1
output frequency setting......................................4-7
output signal delay/hold ....................................4-70
output voltage monitoring....................................4-3
overcurrent restraint..........................................4-41
overload notice advance signal................4-40, 4-41
overload restriction............................................4-40
overtorque.........................................................4-64
P
P/PI switching ...................................................4-58
P24 ............................................................2-7, 2-21
PCC ..................................................................4-59
PCLR ................................................................4-96
PCNT .........................................................4-5, 4-59
phase loss input .......................................2-10, 4-37
phase loss input protection ......................2-10, 4-37
PID....................................................................4-26
PIDC .................................................................4-29
POK ................................................................4-104
positioning end..................................................4-96
Position bias ...................................................4-103
Position command monitor .................................4-5
Position range specification ............................ 4-110
Power monitoring ................................................4-3
PPI ....................................................................4-58
pre-excitation ....................................................4-88
process variable (PV), PID feedback
monitoring ............................................4-1, 4-29
program counter..................................................4-5
program number monitoring................................4-5
programmable controller ...................................2-16
protective function...............................................5-1
Pulse counter .............................................4-5, 4-59
Pulse train frequency input .............................4-104
Pulse train position command ...........................4-94
R
reduced-torque characteristic
(electronic thermal) ..................................... 4-38
reduced torque characteristic (VP) .......... 4-17, 4-85
reduced voltage start ........................................ 4-43
remote operation .............................................. 4-55
remote operator ..................................... Appendix-1
reset ............................................2-8, 3-3, 4-9, 4-53
restart with input frequency...................... 4-34, 4-37
retry after trip .................................................... 4-34
retry selection ................................................... 4-34
reverse rotation signal ...................................... 4-60
reversible ................................................. 4-13, 4-28
RNT .................................................................. 4-64
ROT................................................................ 4-110
rotation direction minitoring................................. 4-1
rotational direction restriction.............................. 4-7
RS ............................................................. 2-9, 4-54
RUN.................................................... 3-3, 4-4, 4-60
Running time over / power-on time
over.................................................... 4-60, 4-64
run command source setting .............................. 4-8
running signal ................................................... 4-61
RV .................................................................... 4-46
RVR ......................................................... 4-60, 4-70
S
Scaled output frequency monitoring ................... 4-2
2nd/3rd control ................................................. 4-49
secondary resistance compensation ................ 4-84
sensorless vector control......................... 4-17, 4-86
servo-on ......................................................... 4-103
SET, SET3........................................................ 4-50
SFT................................................................... 4-51
SF1, SF2, SF3, SF4, SF5, SF6, SF7................ 4-47
sign of the frequency to be added .................... 4-15
sink logic........................................................... 2-16
SJ300 .................................................... Appendix-1
slide switch SW1 ............................ 2-9, Appendix-1
SLV ................................................................... 4-16
software lock..................................................... 4-50
SON.................................................................4-111
source logic ...................................................... 2-16
SPD ................................................................ 4-108
speed deviation maximum ................................ 4-94
Speed biasing ................................................. 4-108
Speed/position switching ................................ 4-103
STA................................................................... 4-57
stabilization constant ........................................ 4-77
start/end frequency setting for external
analog input ................................................ 4-15
start frequency......................................... 4-43, 4-15
start-frequency rate .......................................... 4-15
starting contact signal ....................................... 4-67
start with matching frequency .................. 4-35, 4-51
STAT................................................................. 4-96
stop operation selection...................................... 4-9
STOP/RESET key selection ............................... 4-9
STP .................................................................. 4-57
synchronous operation .......................... 4-99, 4-100