Yaskawa CIMR-LU Drives User Manual
Page 233
C Standards Compliance
YASKAWA ELECTRIC TOEP C710616 38F YASKAWA AC Drive L1000A Quick Start Guide
233
St
an
dar
d
s
Co
mplia
nce
C
Low Voltage Wiring for Control Circuit Terminals
Wire low voltage wires with NEC Class 1 circuit conductors. Refer to national state or local codes for wiring. If external
power supply used, it shall be UL Listed Class 2 power source only or equivalent. Refer to NEC Article 725 Class 1,
Class 2, and Class 3 Remote-Control, Signaling, and Power Limited Circuits for requirements concerning class 1 circuit
conductors and class 2 power supplies.
Table 67 Control Circuit Terminal Power Supply
Drive Short Circuit Rating
This drive is suitable for use on a circuit capable of delivering not more than 100,000 RMS symmetrical amperes,
600 Vac maximum (Up to 240 V in 200 V class drives, up to 480 V for 400 V class drives), when protected by Bussmann
Type FWH fuses as specified in
4A0450
350
410
700
700
1200
FWH-1000A
(1000)
4A0605
400 - 500
584
1000
1000
1600
FWH-1200A
(1200)
Three-Phase 600 V Class
5A0003
2
3.6
15
6.25
10
FWP-50B (50)
5A0004
3
5.1
15
8
15
FWP-60B (60)
5A0006
5
8.3
15
12
20
FWP-60B (60)
5A0010
7.5
12
20
20
35
FWP-70B (70)
5A0013
10
16
30
25
45
FWP-100B (100)
5A0017
15
23
40
40
60
FWP-100B (100)
5A0022
20
31
60
50
90
FWP-125A (125)
5A0027
25
38
75
60
100
FWP-125A (125)
5A0032
30
33
60
50
90
FWP-175A (175)
5A0041
40
44
75
75
125
FWP-175A (175)
5A0052
50
54
100
90
150
FWP-250A (250)
5A0062
60
66
125
110
175
FWP-250A (250)
5A0077
75
80
150
125
225
FWP-250A (250)
5A0099
100
108
175
175
300
FWP-350A (350)
5A0130
125
129
250
225
350
FWP-350A (350)
5A0172
150
158
300
250
400
FWP-600A (600)
5A0200
200
228
400
350
600
FWP-600A (600)
<1> Maximum MCCB Rating is 15 A, or 200% of drive input current rating, whichever is larger. MCCB voltage rating must be 600 Vac or greater.
<2> Maximum Time Delay fuse is 175% of drive input current rating. This covers any Class CC, J or T class fuse.
<3> Maximum Non-time Delay fuse is 300% of drive input current rating. This covers any CC, J or T class fuse.
<4> Class L fuse is also approved for this rating.
Input / Output
Terminal Signal
Power Supply Specifications
Open Collector Outputs
P1, C1, P2, C2, DM+, DM-
Requires class 2 power supply
Digital inputs
S1-S8, SN, SC, SP, HC, H1, H2
Use the internal LVLC power supply of the drive. Use
class 2 for external power supply.
Analog inputs / outputs
+V, -V, A1, A2, AC, AM, FM
Drive Model
CIMR-LU
L1000A in Heavy Duty Mode (C6-01 = 0)
Nominal
Output Power
HP
AC Drive Input
Amps
MCCB Rating
Amps
<1>
Time Delay Fuse
Rating Amps
<2>
Non-time Delay
Fuse Rating
Amps
<3>
Bussmann
Semiconductor
Fuse Rating
(Fuse
Ampere)
<4>
TOEP_C710616_38F_5_0.book 233 ページ ２０１３年１２月４日 水曜日 午前９時５６分