Rockwell Automation 25B PowerFlex 520-Series Adjustable Frequency AC Drive User Manual - Manual (Page 142)

142 Rockwell Automation Publication 520-UM001G-EN-E - September 2014
Chapter 3 Programming and Parameters
Parameter Name No. Parameter Name No. Parameter Name No.
Opt Data Out 1 165 Position Status (1) 387 Shear Pin 2 Time (1) 489
Opt Data Out 2 166 Positioning Mode
(1)
558 Shear Pin2 Level
(1)
488
Opt Data Out 3 167 Power Loss Mode 548 Skip Freq Band 1 449
Opt Data Out 4 168 Power Saved 018 Skip Freq Band 2 451
Opto Out Logic (1) 075 Preset Freq 0 410 Skip Freq Band 3 (1) 453
Opto Out1 Level
(1)
070 Preset Freq 1 411 Skip Freq Band 4
(1)
455
Opto Out1 Sel
(1)
069 Preset Freq 2 412 Skip Frequency 1 448
Opto Out2 Level (1) 073 Preset Freq 3 413 Skip Frequency 2 450
Opto Out2 Sel
(1)
072 Preset Freq 4 414 Skip Frequency 3
(1)
452
Out Phas Loss En 557 Preset Freq 5 415 Skip Frequency 4
(1)
454
Output Current 003 Preset Freq 6 416 Sleep Level 101
Output Freq 001 Preset Freq 7 417 Sleep Time 102
Output Power 017 Preset Freq 8
(1)
418 Sleep-Wake Sel 100
Output Powr Fctr 381 Preset Freq 9
(1)
419 Slip Hz Meter 375
Output RPM 015 Preset Freq 10
(1)
420 Speed Feedback 376
Output Speed 016 Preset Freq 11 (1) 421 Speed Ratio 572
Output Voltage 004 Preset Freq 12
(1)
422 Speed Reference1 047
P Jump 570 Preset Freq 13
(1)
423 Speed Reference2 049
PID 1 Deadband 465 Preset Freq 14 (1) 424 Speed Reference3 051
PID 1 Diff Rate 463 Preset Freq 15 (1) 425 Speed Reg Sel (1) 509
PID 1 Fdback Sel 460 Process Disp Hi 482 Stall Fault Time 492
PID 1 Integ Time 462 Process Disp Lo 481 Start At PowerUp 543
PID 1 Invert Err 467 Process Display 010 Start Boost 531
PID 1 Preload 466 Program Lock 552 Start Source 1 046
PID 1 Prop Gain 461 Program Lock Mod 553 Start Source 2 048
PID 1 Ref Sel 459 Pulse In Scale 537 Start Source 3 050
PID 1 Setpoint 464 Purge Frequency 433 Status @ Fault 1 661
PID 1 Trim Hi 456 PWM Frequency 440 Status @ Fault 2 662
PID 1 Trim Lo 457 RdyBit Mode Act 392 Status @ Fault 3 663
PID 1 Trim Sel 458 RdyBit Mode Cfg 574 Status @ Fault 4 664
PID1 Fdbk Displ 383 Relay 1 Off Time 080 Status @ Fault 5 665
PID1 Setpnt Disp 384 Relay 1 On Time 079 Status @ Fault 6
(1)
666
PID 2 Deadband
(1)
477 Relay Out1 Level 077 Status @ Fault 7
(1)
667
PID 2 Diff Rate (1) 475 Relay Out1 Sel 076 Status @ Fault 8 (1) 668
PID 2 Fdback Sel (1) 472 Relay 2 Off Time (1) 085 Status @ Fault 9 (1) 669
PID 2 Integ Time
(1)
474 Relay 2 On Time
(1)
084 Status @ Fault10
(1)
670
PID 2 Invert Err
(1)
479 Relay Out2 Level
(1)
082 Step Units 0
(1)
200
PID 2 Preload (1) 478 Relay Out2 Sel (1) 081 Step Units 1 (1) 202
PID 2 Prop Gain (1) 473 Reset Meters 555 Step Units 2 (1) 204
PID 2 Ref Sel
(1)
471 Reset to Defalts 053 Step Units 3
(1)
206
PID 2 Setpoint
(1)
476 Reverse Disable 544 Step Units 4
(1)
208
PID 2 Trim Hi (1) 468 RS485 Data Rate 123 Step Units 5 (1) 210
PID 2 Trim Lo
(1)
469 RS485 Format 127 Step Units 6
(1)
212
PID 2 Trim Sel
(1)
470 RS485 Node Addr 124 Step Units 7
(1)
214
PID2 Fdbk Displ
(1)
385 S Curve % 439 Stop Mode 045
PID2 Setpnt Disp (1) 386 Safety Open En (1) 105 Stp Logic 0 (1) 180
Pos Reg Filter
(1)
565 Shear Pin 1 Time 487 Stp Logic 1
(1)
181
Pos Reg Gain
(1)
566 Shear Pin1 Level 486 Stp Logic 2
(1)
182
(1) Parameter is specific to PowerFlex 525 drives only.