GE Industrial Solutions AF-650 GP General Purpose Drive Programming Guide User Manual
Page 77
20
mA
/
desired
maximum
current
x
100 %
i
.
e
. 10
mA
: 20
10
x
100 = 200 %
Illustration 3.34 Output Max Scale
AN-53 Terminal 42 Output Bus Control
Range:
Function:
0 %
*
[0 - 100 %] Holds the level of Output 42 if controlled by
bus.
AN-54 Terminal 42 Output Timeout Preset
Range:
Function:
0 %
*
[0 - 100 %] Holds the preset level of Output 42.
In case of a bus timeout and a timeout
function is selected in AN-50 Terminal 42
Output the output will preset to this level.
AN-55 Terminal 42 Output Filter
Option:
Function:
The following readout analog parameters from
selection in AN-50 Terminal 42 Output have a filter
selected when AN-55 Terminal 42 Output Filter is on:
Selection
0-20 mA
4-20 mA
Motor current (0 - I
max
)
[103]
[133]
Torque limit (0 - T
lim
)
[104]
[134]
Rated torque (0 - T
nom
)
[105]
[135]
Power (0 - P
nom
)
[106]
[136]
Speed (0 - Speed
max
)
[107]
[137]
Table 3.15 Readout Analog Parameters
[0]
*
Off
Filter off
[1]
On
Filter on
3.8.7 AN-6# Analog Output X30/8
Parameters to configure the scaling and limits for Analog
Output 1 associated with OPCGPIO General Purpose Field
Installed Option Module.
AN-60 Terminal X30/8 Output
Option: Function:
Select the function of Terminal X30/8 as an analog
current output. Depending on the selection the output
is either a 0-20 mA or 4-20 mA output. The current
value can be read out in keypad, DR-77 Analog Out
AN-60 Terminal X30/8 Output
Option: Function:
X30/8 [mA]. See options under parameter AN-50
Terminal 42 Output.
AN-61 Terminal X30/8 Min. Scale
Range:
Function:
0 %
*
[0 -
200 %]
Scales the minimum output of the selected
analog signal on terminal X30/8. Scale the
minimum value as a percentage of the maximum
signal value, i.e. 0 mA (or 0 Hz) is desired at 25%
of the maximum output value and 25% is
programmed. The value can never be higher than
the corresponding setting in AN-62 Terminal X30/8
Max. Scale if value is below 100%.
This parameter is active when option module
OPCGPIO General Purpose I/O Option Module is
mounted in the frequency converter.
AN-62 Terminal X30/8 Max. Scale
Range:
Function:
100
%
*
[0 -
200 %]
Scales the maximum output of the selected
analog signal on terminal X30/8. Scale the value
to the desired maximum value of the current
signal output. Scale the output to give a lower
current than 20 mA at full scale or 20 mA at an
output below 100% of the maximum signal
value. If 20 mA is the desired output current at a
value between 0 - 100% of the ful-scale output,
program the percentage value in the parameter,
i.e. 50% = 20 mA. If a current between 4 and 20
mA is desired at maximum output (100%),
calculate the percentage value as follows:
20
mA
/
desired
maximum
current
x
100 %
i
.
e
. 10
mA
: 20 − 4
10
x
100 = 160 %
AN-63 Terminal X30/8 Bus Control
Range:
Function:
0 %
*
[0 - 100 %] Holds the level of Output X30/8 if controlled
by bus.
AN-64 Terminal X30/8 Output Timeout Preset
Range:
Function:
0 %
*
[0 - 100 %] Holds the preset level of Output X30/8.
In case of a bus timeout and a timeout
function is selected in AN-60 Terminal X30/8
Output, the output will preset to this level.
Parameter Descriptions
AF-650 GP Programming Guide
76
DET-618C
3
3