GE Industrial Solutions AF-650 GP General Purpose Drive Programming Guide User Manual
Page 99
PB-16 PCD Read Configuration
[10] Array
Option:
Function:
[1248] Speed Ref. After Ramp [RPM]
[1250] External Reference
[1251] Pulse Reference
[1252] Feedback[Unit]
[1253] Digi Pot Reference
[1257] Feedback [RPM]
[1260] Digital Input
[1261] Terminal 53 Switch Setting
[1262] Analog Input 53
[1263] Terminal 54 Switch Setting
[1264] Analog Input 54
[1265] Analog Output 42 [mA]
[1266] Digital Output [bin]
[1267] Freq. Input #29 [Hz]
[1268] Freq. Input #33 [Hz]
[1269] Pulse Output #27 [Hz]
[1270] Pulse Output #29 [Hz]
[1271] Relay Output [bin]
[1272] Counter A
[1273] Counter B
[1274] Prec. Stop Counter
[1275] Analog In X30/11
[1276] Analog In X30/12
[1277] Analog Out X30/8 [mA]
[1284] Comm. Option STW
[1285] Drive Port CTW 1
[1287] Bus Readout Alarm/Warning
[1290] Alarm Word
[1291] Alarm Word 2
[1292] Warning Word
[1293] Warning Word 2
[1294] Ext. Status Word
[1500] Operating hours
[1501] Running Hours
[1502] kWh Counter
PB-18 Node Address
Range:
Function:
126
*
[0 -
126]
Enter the station address in this parameter or
alternatively in the hardware switch. In order to
adjust the station address in PB-18 Node Address,
the hardware switch must be set to 126 or 127
(that is, all switches set to ‘on’). Otherwise this
parameter displays the actual setting of the
switch.
PB-22 Telegram Selection
Displays the Profibus message configuration.
Option:
Function:
[1]
Standard telegram 1
[100]
*
None
PB-22 Telegram Selection
Displays the Profibus message configuration.
Option:
Function:
[101]
PPO 1
[102]
PPO 2
[103]
PPO 3
[104]
PPO 4
[105]
PPO 5
[106]
PPO 6
[107]
PPO 7
[108]
PPO 8
Read only.
[200]
Custom telegram 1
[202]
Custom telegram 3
PB-23 Parameters for Signals
Array [1000]
Read only
Option: Function:
This parameter contains a list of signals available for
selection in PB-15 PCD Write Configuration and
PB-27 Parameter Edit
Option:
Function:
Parameters can be edited via Profibus, the
standard RS-485 interface, or the keypad.
[0]
Disabled Disables editing via Profibus.
[1]
*
Enabled
Enables editing via Profibus.
PB-28 Process Control
Option:
Function:
Process control (setting of Control Word, speed
reference, and process data) is possible via
either Profibus or standard Network but not
both simultaneously. Local control is always
possible via the keypad. Control via process
control is possible via either terminals or
Network depending on the settings in
O-50 Coasting Select to O-56 Preset Reference
[0]
Disable
Disables process control via Profibus, and
enables process control via standard Network or
Profibus Master class 2.
[1]
*
Enable
cyclic
master
Enables process control via Profibus Master Class
1, and disables process control via standard
Network or Profibus Master class 2.
PB-44 Fault Message Counter
Range:
Function:
0
*
[0 - 65535] This parameter displays the number of error
events stored in PB-45 Fault Code and
PB-47 Fault Number. The maximum buffer
Parameter Descriptions
AF-650 GP Programming Guide
98
DET-618C
3
3