GE Industrial Solutions AF-650 GP General Purpose Drive Programming Guide - Manual (Page 90)

O-35 Minimum Response Delay
Range: Function:
10 ms * [1 - 10000 ms] Specify the minimum delay time
between receiving a request and
transmitting a response. This is used for
overcoming modem turnaround delays.
O-36 Max Response Delay
Range: Function:
10001 ms * [11 - 10001
ms]
Specify the maximum permissible
delay time between transmitting a
request and receiving a response. If a
response from the frequency converter
is exceeding the time setting then it
will be discarded.
O-37 Max Inter-Char Delay
Range: Function:
25.00 ms * [0.00 -
35.00 ms]
Specify the maximum permissible time
interval between receipt of two bytes.
This parameter activates time-out if
transmission is interrupted.
This parameter is active only when
O-30 Protocol is set to [1] Drive MC
protocol.
3.10.4 O-4# Drive MC Port Settings
Parameters to configure the standard telegram or custom
telegram for the GE drive port.
O-40 Telegram Selection
Option: Function:
[1] * Standard telegram 1 Enables use of freely configurable
messages or standard messages for
the Drive port.
[100] None
[101] PPO 1
[102] PPO 2
[103] PPO 3
[104] PPO 4
[105] PPO 5
[106] PPO 6
[107] PPO 7
[108] PPO 8
[200] Custom telegram 1 Enables use of freely configurable
messages or standard messages for
the Drive port.
[202] Custom telegram 3
O-41 Parameters for Signals
Option: Function:
[0] * None This parameter contains
a list of signals available
O-41 Parameters for Signals
Option: Function:
for selection in O-42 PCD
Write Configuration and
O-43 PCD Read Configu-
ration.
[7] Accel Time 1
[8] Decel Time 1
[15] Motor Speed High Limit [Hz]
[16] Motor Speed Low Limit [Hz]
[17] Motor Speed High Limit [RPM]
[18] Motor Speed Low Limit [RPM]
[40] Torque Limiter (Driving)
[41] Torque Limiter (Braking)
[52] Minimum Reference
[53] Maximum Reference
[62] Catch up/slow Down Value
[110] Accel Time 2
[111] Decel Time 2
[190] Digital & Relay Bus Control
[193] Pulse Out #27 Bus Control
[195] Pulse Out #29 Bus Control
[197] Pulse Out #X30/6 Bus Control
[222] Jog Accel/Decel Time
[223] Quick Stop Decel Time
[515] Readout: actual setup
[653] Terminal 42 Output Bus Control
[663] Terminal X30/8 Bus Control
[748] PCD Feed Forward
[890] Bus Jog 1 Speed
[891] Bus Jog 2 Speed
[1201] Reference [Unit]
[1202] Reference %
[1203] Status Word
[1205] Main Actual Value [%]
[1209] Custom Readout
[1210] Power [kW]
[1211] Power [hp]
[1212] Motor Voltage
[1213] Frequency
[1214] Motor current
[1215] Frequency [%]
[1216] Torque [Nm]
[1217] Speed [RPM]
[1218] Motor Thermal
[1219] KTY sensor temperature
[1220] Motor Angle
[1221] Torque [%] High Res.
[1222] Torque [%]
[1225] Torque [Nm] High
[1230] DC Link Voltage
[1232] Brake Energy /s
[1233] Brake Energy /2 min
[1234] Heatsink Temp.
Parameter Descriptions AF-650 GP Programming Guide
DET-618C 89
3 3