Lenze EVF9383 - Manual (Page 452)

Appendix
Index
14
14.2
l
14.2−4 EDSVF9383V EN 7.1−04/2012
Imax limit in motor mode, 6.6−14 , 8.2−27 , 8.2−42 , 8.5−4
Incremental encoder
− At X8, 5.8−2 , 6.7−2
− at X9, 5.8−3 , 6.7−2
− operation with, 8.2−48
− with HTL level, 5.8−3 , 6.7−2
− With TTL level, 5.8−2 , 6.7−2
Input signals
− Analog, Configuration, 6.5−4
− Digital, Configuration, 6.5−1
Inputs
− Digital, Response times, 6.5−1
− KTY, 6.6−10
− PTC, 6.6−8
Interaction with compensation equipment, 5.2−2
Interferences, eliminating EMC interferences, 5.3−6
Internal motor control
− V/f characteristic control (MCTRL1), setting of V/f
characteristic, 8.2−31
− with vector control (MCTRL2)
torque control with speed limitation, 8.2−53
torque limitation, 8.2−50
Internal motor control (MCTRL)
− inhibiting the direction of rotation, 8.2−39 , 8.2−61
− limiting output current, 8.2−52
− limiting the output current, 8.2−32
− limiting the speed setpoint, 8.2−31 , 8.2−47
− quick stop (QSP), 8.2−33 , 8.2−54
− speed control, 8.2−31 , 8.2−48
− speed setpoint selection, 8.2−31 , 8.2−47
− with vector control (MCTRL2), 8.2−40
J
JOG setpoint, 8.5−6
Jumper X3, for input range of analog setpoint selection,
5.6−9
K
Keypad EMZ9371BC, Changing parameters, 7.2−4 , 7.2−6 ,
7.2−9
Keypad XT EMZ9371BC
− function keys, 7.2−4
− status display, 7.2−2
KTY motor monitoring, 6.6−10
L
Labelling, controller, 1.2−1
LED display, 9.2−1
Legal regulations, 1.2−1
Liability, 1.2−2
Light−emitting diodes, 9.2−1
M
Mains cable, Dimensioning of, 5.2−4
Mains connection, 5.3−1
− 400 V devices, 5.4−3 , 5.5−7
− 400/500 V devices, 5.4−3 , 5.5−7
− fuses for the, 5.4−6 , 5.5−10
mains connection, cable cross−sections for the, 5.4−6 ,
5.5−10
Manufacturer, 1.2−1
Master frequency input (DFIN), 8.2−5
Master frequency output (DFOUT), 8.2−8
Master frequency processing (DFSET), 8.2−18
Master frequency ramp−function generator (DFRFG1),
8.2−13
Master/slave
− Connecting control cables between the devices, 5.5−5
− installing the DC busbars, 5.5−4
Maximum speed, 6.10−1 , 8.2−26 , 8.2−41 , 8.5−3
Menu structure, XT EMZ9371BC keypad, 7.2−11
Message, 8.3−1
Minimum speed, 6.10−1 , 8.2−26 , 8.2−41 , 8.5−3
Mobile systems, 5.2−3
Monitoring, 8.3−1
− bus off, 8.3−2
− configuring, 8.4−1
− Current load of controller, Ixt monitoring, 8.3−4
− Current load of motor, I2 x t−monitoring, 2.2−1 , 8.3−6
− DC−bus voltage, 8.3−8
− Earth fault in motor cable (OC2), 8.3−3
− Exceeding of the maximum speed (NMAX), 8.3−3
− External error (EEr), 8.3−8
− Failure of a motor phase (LP1), 8.3−4
− Heatsink temperature, 8.3−7
− Monitoring times for process data input objects, 8.3−2
− motor cable overcurrent (OC1), 8.3−3
− motor temperature, 8.3−5
− overload acceleration, deceleration (OC3), 8.3−3
− possible responses, 8.4−1
− reset node, 8.3−2
− responses, 8.3−1
message, 8.3−1
TRIP, 8.3−1
warning, 8.3−1