Lenze EVF9383 - Manual (Page 454)

Appendix
Index
14
14.2
l
14.2−6 EDSVF9383V EN 7.1−04/2012
Power system, 3.1−2
Protection against unexpected start−up, 11.1−1
− operating mode, 11.2−2
− safety relay, 3.4−1 , 11.3−1
Protection of persons, 2.3−1
− with earth−leakage circuit breaker, 5.2−2
PTC motor monitoring, 6.6−8
Q
QSP (quick stop), 8.2−33 , 8.2−54
Quick stop, 6.10−4
Quick stop (QSP), 8.2−33 , 8.2−54
Quick stop deceleration time, 6.10−4 , 8.2−29 , 8.2−45 ,
8.5−11
R
Rated data, 12.2−1
− for 400 V mains voltage, 3.6−1
− for 500 V mains voltage, 3.6−2
− integrated brake transistor, 12.3−1
Rated motor current, 6.6−1 , 6.6−16 , 6.8−9 , 8.2−44 ,
8.5−9
Rated motor frequency, 6.6−1 , 6.6−16 , 6.8−9 , 8.2−29 ,
8.2−44 , 8.5−9
Rated motor power, 6.6−1 , 6.8−8 , 8.5−8
Rated motor speed, 6.6−1 , 6.6−16 , 6.8−9 , 8.2−29 , 8.2−44
, 8.5−9
Rated motor voltage, 6.6−2 , 6.6−16 , 6.8−5 , 6.8−9 ,
8.2−29 , 8.2−44 , 8.5−9
Reaction times of digital inputs, 6.5−1
Relay output, Configuration, 6.5−3
Residual hazards, 2.3−1
Responses, 8.3−1
− message, 8.3−1
− TRIP, 8.3−1
− warning, 8.3−1
Running optimisation, 6.11−1
S
Safe standstill, 11.1−1
Safe torque off, 11.1−1
− Function deactivated, 5.6−7
− functional test, 11.4−2 , 11.4−5
− operating mode, 11.2−2
− safety relay, 3.4−1 , 11.3−1
Safe torque offt, Function active, 5.6−4
Safety, safety engineering, 11−1
Safety engineering, 11−1
Safety function
− functional test, 11.4−2 , 11.4−5
− Safe torque off, 11.1−1
Safety instructions, 2−1
− definition, 1.4−1
− layout, 1.4−1
Safety relay, 3.4−1 , 11.3−1
− Connector X11
Terminal assignment, 11.3−2
Wiring, 11.3−2
Safety relay KSR, Terminal assignment, 5.6−9 , 11.3−2
Selecting the operating mode, speed mode, setting
acceleration and deceleration times, 6.10−3
Selection, operating mode, 6.1−1 , 6.8−1
Selection of motor type, 6.6−1 , 8.2−29 , 8.2−44 , 8.5−9
Selection of the feedback system, 6.7−1 , 8.2−42 , 8.5−4
Setting integral action component, 8.2−49
Setting the acceleration time, 6.10−3
Setting the deceleration time, 6.10−3
Setting the feedback system, 6.7−1
Setting the speed feedback, 6.7−1
Shielding
− DC−bus cable, 5.4−4 , 5.5−8
− motor cable, 5.4−7 , 5.5−11
Site altitude, 3.1−2
Slip compensation, 6.11−1 , 8.2−39 , 8.2−61
Speed control, 8.2−31 , 8.2−48
− adapting the speed controller, 8.2−48
− at vector control (MCTRL2), adapting the speed
controller, 8.2−31
− with vector control (MCTRL2)
setting integral action component, 8.2−49
speed feedback, 8.2−48
temperature detection, 8.2−49
Speed feedback, 8.2−48
Speed mode, setting acceleration and deceleration times,
6.10−3
Speed oscillations, 6.11−3
Speed setpoint limitation, 8.2−31 , 8.2−47
Speed setpoint selection, 8.2−31 , 8.2−47
Stability, of the motor, 8.2−50
Status display, keypad XT EMZ9371BC, 7.2−2
Status word AIF, 8.5−14 , 9.1−2
Stopping, 6.10−1