Low voltage wiring for control circuit terminals – Yaskawa AC Drive Z1000 User Manual
Page 370
Model
Nominal Output
Power (HP)
AC Drive Input
(A)
MCCB Rating (A)
<1>
Time Delay Fuse
Rating (A)
<2>
Non-time Delay
Fuse Rating (A)
<3>
Bussmann
Semiconductor
Fuse Model
(Fuse Ampere)
<4>
2A0088
30
88
175
150
250
FWH-225A (225)
2A0114
40
114
225
175
300
FWH-250A (250)
2A0143
50
143
250
250
400
FWH-275A (275)
2A0169
60
169
300
275
500
FWH-350A (350)
2A0211
75
211
400
350
600
FWH-400A (400)
2A0273
10
273
500
450
<5>
FWH-450A (450)
2A0343
125
343
600
600
FWH-600A (600)
2A0396
150
396
700
<5>
FWH-600A (600)
Three-Phase 400 V Class
4A0005
3
4.8
15
8
12
FWH-40B (40)
4A0008
5
7.6
15
12
20
FWH-40B (40)
4A0011
7.5
11
20
17.5
30
FWH-45B (45)
4A0014
10
14
25
20
40
FWH-45B (45)
4A0021
15
21
40
35
60
FWH-60B (60)
4A0027
20
27
50
45
80
FWH-60B (60)
4A0034
25
34
60
50
100
FWH-125B(125)
4A0040
30
40
75
70
110
FWH-150B (150)
4A0052
40
52
100
90
150
FWH-200B (200)
4A0065
50
65
125
110
175
FWH-225A (225)
4A0077
60
77
150
125
225
FWH-225A (225)
4A0096
75
96
175
150
275
FWH-225A (225)
4A0124
100
124
225
200
350
FWH-250A(250)
4A0156
125
156
300
250
450
FWH-300A (300)
4A0180
150
180
350
300
500
FWH-350A (350)
4A0240
200
240
450
400
<5>
FWH-400A (400)
4A0302
250
302
600
500
FWH-600A (600)
4A0361
300
346
600
600
1000
<6>
FWH-800A (800)
4A0414
350
410
800
700
1200
<6>
FWH-800A (800)
4A0480
400
480
900
<5>
<5>
FWH-700A (700)
4A0590
500
590
1100
FWH-1000A
(1000)
<1> Maximum MCCB rating is 15 A, or 200% of drive input current rating, whichever value is larger. MCCB voltage rating must be 600 Vac or greater.
<2> Maximum Time delay fuse is 175% or drive input current rating. This covers any Class J, T, or CC fuse.
<3> Maximum Non-time delay fuse is 300% of drive input current rating. This covers any Class J, T, or CC fuse.
<4> When using semiconductor fuses, Bussmann FWH fuses are required for UL compliance.
<5> Consult factory.
<6> Class L fuse is also approved for this rating.
n
Low Voltage Wiring for Control Circuit Terminals
Wire low voltage wires with NEC Class 1 circuit conductors. Refer to national state or local codes for wiring. The external
power supply shall be a UL listed Class 2 power supply source or equivalent only. Refer to NEC Article 725 Class 1, Class
2, and Class 3 Remote-Control, Signaling, and Power Limited Circuits for requirements concerning class 1 circuit conductors
and class 2 power supplies.
Table D.5 Control Circuit Terminal Power Supply
Input / Output
Terminal Signal
Power Supply Specifications
Multi-function digital inputs
S1, S2, S3, S4, S5, S6, S7, SC, SP, SN
Use the internal control power supply of the drive or an
external class 2 power supply.
Multi-function analog inputs
+V, A1, A2, AC, FM, AM
D.3 UL/cUL Standards
370
YASKAWA ELECTRIC TOEP C710616 45E YASKAWA AC Drive – Z1000 User Manual