Yaskawa AC Drive Z1000 User Manual
Page 389
oPr ................................................................................ 213
Optional 24 V DC power supply connector cover .... 30, 31, 32, 33, 34, 35
Option card connection error (CN5) ......................................... 211
Option Card Connection Error at Option Port CN5........................ 210
Option card connector (CN5) ...................................................37
Option card error occurred at option port CN5 ............................. 211
Option Card External Fault.............................................. 207, 219
Option Card Fault at Option Port CN5....................................... 211
Option Communication Error ........................................... 205, 218
Option Frequency Reference .................................................. 334
Option Installation .............................................................. 248
Option Monitors 1 to 20 ....................................................... 335
Oscillation or Hunting.......................................................... 240
Output Current .................................................................. 329
Output Current 1 during Speed Search ...................................... 159
Output Current at Previous Fault ............................................. 331
Output Current Imbalance ..................................................... 209
Output Frequency............................................................... 329
Output Frequency after Soft Start ............................................ 330
Output Frequency at Previous Fault.......................................... 331
Output Frequency is not as High as Frequency Reference ................ 241
Output Frequency Reduction During Overheat Alarm .................... 181
Output Frequency Resolution ................................................. 272
Output Ground Fault Detection Selection ............................. 182, 314
Output Phase Loss .............................................................. 209
Output Phase Loss Detection Level for Dynamic Audible Noise Control ...
Output Phase Loss Protection ................................................. 314
Output Phase Loss Protection Selection ..................................... 182
Output Power.................................................................... 329
Output Power at Previous Fault............................................... 331
Output Terminal Status ........................................................ 329
Output Terminal Status at Previous Fault ................................... 331
Output Voltage at Previous Fault ............................................. 331
Output Voltage Detection Fault......................................... 217, 224
Output Voltage Reference ..................................................... 329
Output Voltage Reference (Vd)............................................... 335
Output Voltage Reference (Vq)............................................... 335
ov............................................................................ 214, 222
ov2 ................................................................................ 214
ov2 Detect Time ................................................................ 326
Overcurrent ...................................................................... 210
Overcurrent Detection Gain ............................................. 183, 314
Overexcitation Deceleration Gain ............................................ 316
Overexcitation Operation Selection .......................................... 316
Overheat 1 (Heatsink Overheat) .............................................. 211
Overheat Alarm Level.................................................... 180, 313
Overheat Pre-Alarm Operation Selection ............................. 180, 313
Overload Protection ............................................................ 272
Overload Tolerance............................... 266, 267, 268, 269, 270, 271
Overtorque 1..................................................................... 222
Overtorque Detection 1 ........................................................ 213
Overvoltage...................................................................... 214
Overvoltage 2 ................................................................... 214
Overvoltage Protection......................................................... 272
ov Suppression Function Selection........................................... 311
P
Panel Cut-Out Dimensions ......................................................45
Parameter Access Level........................................................ 152
Parameter Range Setting Error................................................ 225
Parameter Selection Error ..................................................... 226
Parameter Settings .............................................................. 115
Parameters to Minimize Motor Hunting and Oscillation .................. 200
PASS ............................................................................. 223
Password ......................................................................... 152
Password Settings............................................................... 152
Peak Hold Current .............................................................. 333
Peak Hold Output Frequency ................................................. 333
Permanent Magnet Motor Control............................................ 122
PF ................................................................................. 214
Phase Order Selection .......................................................... 157
PI Accel/Decel Time ........................................................... 164
PI Feedback...................................................................... 334
PI Feedback Function Selection .............................................. 165
PI Feedback High Detection Level ........................................... 166
PI Feedback High Detection Time ........................................... 166
PI Feedback Loss ......................................................... 208, 220
PI Feedback Loss Detection Selection ....................................... 162
PI Feedback Low Detection Level ........................................... 163
PI Feedback Low Detection Time ............................................ 163
PI Feedback Offset ............................................................. 166
PI Function Setting ............................................................. 161
PI Input (feedback) ............................................................. 334
PI Input Limit ................................................................... 166
PI Maximum Boost Time...................................................... 165
PI Monitors ...................................................................... 192
PI Offset Adjustment ........................................................... 161
PI Output......................................................................... 334
PI Output Fault .................................................................. 240
PI Output Gain Setting ......................................................... 162
PI Output Level Selection ..................................................... 162
PI Output Limit ................................................................. 161
PI Output Lower Limit......................................................... 166
PI Output Monitor Calculation Method...................................... 167
PI Output Reverse Selection .................................................. 162
PI Primary Delay Time Constant ............................................. 162
PI Setpoint ....................................................................... 334
PI Setpoint Boost Setting ...................................................... 165
PI Setpoint Display Digits ..................................................... 166
PI Setpoint Monitor Unit Selection........................................... 168
PI Setpoint Scaling ............................................................. 164
PI Setpoint Selection ........................................................... 164
PI Setpoint User Display....................................................... 166
PI Setpoint Value ............................................................... 164
PI Sleep Delay Time ........................................................... 163
PI Sleep Function Start Level ................................................. 163
PI Sleep Input Source .......................................................... 164
PI Snooze Deactivation Level................................................. 165
PI Snooze Delay Time ......................................................... 165
PI Snooze Feedback Level .................................................... 165
PI Snooze Level................................................................. 165
PI Square Root Gain............................................................ 166
PI Unit Selection ................................................................ 167
PM Motor Auto-Tuning Mode Selection .................................... 147
PM Motor Base Frequency .................................................... 148
PM Motor d-Axis Inductance ................................................. 148
PM Motor Induced Voltage Constant ........................................ 149
PM Motor Parameter Settings................................................. 143
PM Motor q-Axis Inductance ................................................. 149
PM Motor Rated Current ...................................................... 148
Index
YASKAWA ELECTRIC TOEP C710616 45E YASKAWA AC Drive – Z1000 User Manual
389