Yaskawa AC Drive Z1000 User Manual
Page 386
FbH ......................................................................... 208, 220
FbL ......................................................................... 208, 220
FE ...................................................................................91
Ferrule Dimensions...............................................................94
Ferrule Terminal Types and Sizes ..............................................94
Ferrule-Type Wire Terminals ...................................................94
Fine-Tuning Open Loop Vector Control for PM Motors.................. 199
Fine-Tuning V/f Control ....................................................... 198
FM ..................................................................................92
Fn1................................................................................ 208
Forward/Reverse Run Command Input Error............................... 219
Frequency Accuracy (Temperature Fluctuation) ........................... 272
Frequency Control Range...................................................... 272
Frequency Reduction Rate during Overheat Pre-Alarm............. 183, 314
Frequency Reference ........................................................... 329
Frequency Reference and Frequency Related Monitor Custom Units 1 318
Frequency Reference and Frequency Related Monitor Custom Units 1 to 3
..................................................................................... 187
Frequency Reference and Frequency Related Monitor Custom Units 2 318
Frequency Reference and Frequency Related Monitor Custom Units 3 319
Frequency Reference at Previous Fault ...................................... 331
Frequency Reference at Reference Loss............................... 138, 312
Frequency Reference Display Units.......................................... 318
Frequency Reference from MEMOBUS/Modbus Comm. ................ 334
Frequency Reference Inputs.....................................................91
Frequency Reference Loss Detection Selection ...................... 138, 312
Frequency Reference Lower Limit ........................................... 133
Frequency Reference Monitor Content During PI ......................... 166
Frequency Reference Selection 1............................................. 236
Frequency Reference Selection for AUTO Mode .......................... 127
Frequency Reference Selection for AUTO mode .......................... 282
Frequency Reference Setting / Decimal Display ........................... 318
Frequency Reference Setting and User-Set Display ....................... 318
Frequency Reference Setting Method Selection...................... 141, 319
Frequency Reference Source Selection ...................................... 334
Frequency Reference Upper Limit ........................................... 133
Frequency Setting Resolution ................................................. 272
Frequency Setting Signal ...................................................... 272
Front Cover .............................................30, 31, 32, 33, 34, 35, 36
Front Cover Screw........................................................... 34, 35
Fuse Selection .........................................................81, 362, 369
G
General Safety Information......................................................14
GF................................................................................. 209
Ground Fault .................................................................... 209
Ground Terminal..................................................................37
Ground Wiring ....................................................................87
Ground Wiring for Multiple Drives ............................................87
H
H1 Multi-Function Digital Input Selections................................. 300
H3-01 ............................................................................. 101
H3-09 ............................................................................. 101
H3-13 ....................................................................... 200, 240
H3 Multi-Function Analog Input Settings................................... 306
HAND/AUTO During Run Selection........................................ 325
HAND Frequency Reference 1 ............................................... 325
HAND Frequency Reference Selection...................................... 325
HAND Key ...................................................................... 107
HAND Key Function Selection (HOA Keypad) ........................... 325
HAND Light..................................................................... 107
HAND Mode Behavior Selection ............................................ 325
HAND Mode PI Selection..................................................... 325
HCA .............................................................................. 220
Heatsink .................................................30, 31, 32, 33, 34, 35, 36
Heatsink Cooling Fan Off-Delay Time ...................................... 182
Heatsink Cooling Fan Operation Delay Time .............................. 314
Heatsink Cooling Fan Operation Selection............................ 182, 314
Heatsink Overheat ........................................................ 211, 221
Heatsink Temperature.......................................................... 333
High Current Alarm Selection .......................................... 185, 314
High-Slip Braking Current Limit ............................................. 316
High-Slip Braking Deceleration Frequency Width......................... 316
High-Slip Braking Dwell Time at Stop ...................................... 316
High-slip Braking oL........................................................... 213
High-Slip Braking Overload Time ........................................... 316
High-Slip Suppression Current Level........................................ 316
HOA Keypad .............................................................34, 35, 30
HOA keypad.....................................................30, 31, 32, 33, 36
HOA Keypad Battery Voltage Low .......................................... 205
HOA Keypad Connection Fault .............................................. 213
HOA Keypad Dimensions .......................................................47
HOA Keypad Display Selection ........................................ 186, 318
HOA Keypad Installation Methods and Required Tools ....................47
HOA Keypad Menu and Screen Structure .................................. 111
HOA Keypad Remote Installation..............................................47
HOA Keypad Remote Usage....................................................46
Humidity ...........................................................................42
Hunting Prevention Gain ...................................................... 198
Hunting Prevention Gain Setting ............................................. 316
Hunting Prevention Gain while in Reverse ................................. 316
Hunting Prevention Selection ................................................. 316
Hunting Prevention Time Constant .......................................... 316
Hybrid IC Failure ............................................................... 207
I
I/O Connections...................................................................92
IEC/EN 61800-3 Filters........................................................ 367
iFEr ............................................................................... 231
IG ...................................................................................92
IGBT Maintenance Time (50%) .............................................. 221
IGBT Maintenance Time (90%) ............................................. 223
Induced Voltage Constant Unit Selection ................................... 149
Initialize Parameters...................................................... 152, 141
Initial Operation................................................................. 119
Input Current ...................................... 266, 267, 268, 269, 270, 271
Input Fuses.............................................................81, 362, 369
Input Phase Detection Level .................................................. 314
Input Phase Loss ................................................................ 214
Input Phase Loss Detection Level ............................................ 181
Input Phase Loss Protection Selection ................................. 181, 313
Input Terminal Status .......................................................... 329
Input Terminal Status at Previous Fault ..................................... 331
Input Voltage Setting........................................................... 134
Inrush Prevention Circuit Fault ............................................... 216
Inrush Prevention Relay Maintenance Setting .............................. 320
Installation Area ..................................................................42
Installation Environment.........................................................42
Installation Method Selection ........................................... 184, 314
Index
386
YASKAWA ELECTRIC TOEP C710616 45E YASKAWA AC Drive – Z1000 User Manual