Yaskawa AC Drive Z1000 - Manual (Page 385)

DC Injection Braking Start Frequency....................................... 129
DC Injection Braking Time at Start .......................................... 158
DC Injection Braking Time at Stop .......................................... 158
DC Injection Braking to Stop ................................................. 130
Deceleration Rate Calculation Gain.......................................... 311
Deceleration Time .............................................................. 132
Deceleration Time at Stall Prevention during Acceleration............... 311
Desired DC Bus Voltage during KEB ....................................... 310
Device Object ................................................................... 352
dFPS .............................................................................. 231
Diagnosing and Resetting Faults ............................................. 233
Dimensions for IP00/Open-Type Enclosure: 200 V Class ..................58
Dimensions for IP00/Open-Type Enclosure: 400 V Class ..................58
Dimensions for IP20/NEMA Type 1 Enclosure: 200 V Class..............52
Dimensions for IP20/NEMA Type 1 Enclosure: 400 V Class..............52
DIP Switch S2.....................................................................37
dnE................................................................................ 219
Down Arrow Key ............................................................... 107
Drive/kVA Selection ........................................................... 319
Drive Capacity Setting Fault .................................................. 225
Drive Cover......................................................32, 33, 34, 35, 36
Drive Derating Data ............................................................ 276
Drive Disabled .................................................................. 219
Drive Mode ................................................................ 112, 115
Drive Model Mismatch ........................................................ 231
Drive Models and Types.........................................................49
Drive Model Selection ......................................................... 188
Drive Mode Unit Monitor Selection ................................... 185, 318
Drive Nameplate ..................................................................27
Drive Operations by BACnet ................................................. 346
Drive Operation Status at Previous Fault.................................... 331
Drive Overheat Warning....................................................... 222
Drive Overload.................................................................. 213
Drive Ready ..................................................................... 103
Drive Slave Address...................................................... 176, 342
Drive Specifications ............................................................ 272
Drive Status...................................................................... 330
Drive Transmit Wait Time .............................................. 177, 343
Drive Unit Signal Fault ........................................................ 207
Drive Watt Loss Data .......................................................... 274
Dynamic Audible Noise Control Function Selection ...................... 321
E
E1-04 ............................................................................. 241
E1-08 ............................................................................. 198
E1-10 ............................................................................. 198
E2-03 ............................................................................. 229
EEPROM Memory Data Error................................................ 206
EEPROM Write Error.......................................................... 208
EF ................................................................................. 219
EF0 ......................................................................... 207, 219
EF1 ......................................................................... 207, 220
EF2 ......................................................................... 207, 220
EF3 ......................................................................... 207, 220
EF4 ......................................................................... 207, 220
EF5 ......................................................................... 207, 220
EF6 ......................................................................... 207, 220
EF7 ......................................................................... 207, 220
EMC Filter and Drive Installation for CE Compliance.............. 365, 366
EMC Filter Installation......................................................... 363
EMC Filters...................................................................... 363
EMC filter switch SW1 ..........................................................37
EMC filter switch SW2 ..........................................................37
EMC Guidelines ................................................................ 362
EMC Guidelines Compliance ................................................. 363
Emergency Override Reference Selection................................... 326
Emergency Override Speed ................................................... 326
Enclosure Types ..................................................................29
End................................................................................ 231
End3 .............................................................................. 229
End4 .............................................................................. 229
End5 .............................................................................. 229
End7 .............................................................................. 229
Energy Saving Constants Error ............................................... 227
Enter Command................................................................. 178
Enter command necessary ............................................... 178, 344
Enter command not necessary .......................................... 179, 344
Enter Command Types......................................................... 353
Enter Data from the Motor Nameplate....................................... 145
ENTER Key ..................................................................... 107
Er-01.............................................................................. 229
Er-02.............................................................................. 229
Er-03.............................................................................. 230
Er-04.............................................................................. 230
Er-05.............................................................................. 230
Er-08.............................................................................. 230
Er-09.............................................................................. 230
Er-12.............................................................................. 230
Err................................................................................. 208
Error Reading Data ............................................................. 232
Errors and Displays When Using the Copy Function...................... 204
Error Writing Data.............................................................. 231
European Standards ............................................................ 362
Excessive Motor Oscillation and Erratic Rotation ......................... 239
Excessive PI Feedback ................................................... 208, 220
Exterior and Mounting Dimensions ............................................49
External Fault ............................................................. 207, 220
External Interlock............................................................... 103
F
F1/F2 Key Function Selection ................................................ 187
F1 Key Function Selection .................................................... 319
F2 Key Function Selection .................................................... 319
FAn ............................................................................... 208
Fan Application ................................................................. 124
Fan Bracket .......................................................... 32, 33, 34, 35
Fan Cover ..........................................................................30
Fan Finger Guard .................................................................30
Fan Guard........................................................32, 33, 34, 35, 36
Fan with PI Control Application.............................................. 125
Fault Causes and Solutions .................................................... 205
Fault Detection .................................................................. 205
Fault Displays ................................................................... 205
Fault History..................................................................... 192
Fault Relay Output................................................................92
Fault Reset Interval Time................................................ 179, 312
Fault Reset Methods............................................................ 201
Fault Reset Operation Selection ........................................ 179, 313
Faults ....................................................................... 201, 202
Fault Trace................................................................. 192, 233
Index
YASKAWA ELECTRIC TOEP C710616 45E YASKAWA AC Drive – Z1000 User Manual 385