Yaskawa AC Drive Z1000 User Manual
Page 390
PM Motor Rated Power........................................................ 148
PM Motor Rated Voltage ...................................................... 148
PM Motor Stator Resistance .................................................. 148
PM Motor Type ................................................................. 148
Powering Up the Drive......................................................... 123
Power Ratings (Three-Phase 200 V Class).......... 266, 267, 268, 269, 270
Power Ratings (Three-Phase 400 V Class).................................. 271
Predefined V/f Patterns ........................................................ 172
Preface..............................................................................12
Preparing the Ends of Shielded Cables ........................................98
Present Value Access........................................................... 348
Preset Reference Timing Diagram ........................................... 170
Previous Fault ................................................................... 330
Programming Errors............................................................ 225
Programming Mode ...................................................... 112, 115
Proportional Gain Setting (P) ................................................. 161
Protective Cover ..................................................................79
Protective Covers, Reattaching .................................................71
Protective Covers, Removing ...................................................70
Pull-In Current .................................................................. 317
Pull-In Current Compensation Time Constant.............................. 317
Pull-In Current during Accel/Decel for PM................................. 215
Pull-In Current Level for PM Motor Tuning................................ 149
Pump (Secondary) Application ............................................... 126
Pump with PI Control Application .......................................... 126
R
R-....................................................................................92
R/L1 ................................................................................81
R+...................................................................................92
Ramp to stop .................................................................... 129
Rated Current Setting Alarm .................................................. 229
Rated Output Capacity ........................... 266, 267, 268, 269, 270, 271
Rated Output Current............................. 266, 267, 268, 269, 270, 271
Rated Slip Error ................................................................. 230
Rated Voltage, Rated Frequency ............... 266, 267, 268, 269, 270, 271
rdEr ............................................................................... 232
READ ............................................................................ 189
rEAd .............................................................................. 232
Reading BACnet Drive Parameters .......................................... 353
Reading Parameter Settings ................................................... 232
Real Time Clock Setting................................................. 114, 190
Reattaching the Front Cover ....................................................77
Reattaching the HOA Keypad ..................................................72
Reattaching the Protective Cover...............................................80
Reattaching the Terminal Cover ................................................71
Removing the Front Cover ......................................................73
Removing the HOA Keypad ....................................................72
Removing the Protective Cover.................................................79
Removing the Terminal Cover..................................................70
RESET Key...................................................................... 107
Resistance Tuning Error ....................................................... 229
Response Messages from Drive to Master .................................. 347
Return Fan with PI Control Application..................................... 125
Reverse Operation Selection .................................................. 157
Reverse Operation Selection 2 by PI Output................................ 168
Rotational Auto-Tuning for V/f Control..................................... 142
RS-485 Interface ................................................................ 341
RTS Control Selection ................................................... 178, 343
Rubber Bushing ...................................................................30
Run Command/Frequency Reference Source Selection Error............ 226
Run Command at Power Up................................................... 157
Run Command Method Selection ...................................... 179, 344
Run Command Selection ...................................................... 236
Run Command Selection 1 .................................................... 129
RUN Command Selection for AUTO mode ................................ 282
Run Command Source Selection ............................................. 334
S
S- ....................................................................................92
S: Special Parameters .......................................................... 321
S/L2.................................................................................81
S+ ...................................................................................92
S1 ...................................................................................91
S1: Dynamic Noise Control Function........................................ 321
S2 ...................................................................................91
S2: Sequence Timers ........................................................... 321
S3 ...................................................................................91
S4 ...................................................................................91
S5 ...................................................................................91
S6 ...................................................................................91
S7 ...................................................................................91
SAFE ............................................................................. 223
Safety Hazard Definitions .......................................................14
Safety Information................................................................14
SC...................................................................................91
Screw ................................................................. 30, 32, 33, 36
S-Curve Characteristics ........................................................ 200
SE ................................................................................. 223
Secondary PI Disable Mode................................................... 324
Secondary PI Display Digits .................................................. 323
Secondary PI Enable Selection ............................................... 323
Secondary PI Feedback Detection Selection ................................ 324
Secondary PI High Feedback Detection Time .............................. 324
Secondary PI High Feedback Level .......................................... 324
Secondary PI Integral Limit Setting.......................................... 324
Secondary PI Integral Time Setting .......................................... 324
Secondary PI Low Feedback Detection Level .............................. 324
Secondary PI Low Feedback Detection Time .............................. 324
Secondary PI Output Level Selection ........................................ 324
Secondary PI Output Lower Limit ........................................... 324
Secondary PI Output Upper Limit............................................ 324
Secondary PI Proportional Gain Setting ..................................... 324
Secondary PI Setpoint Value.................................................. 324
Secondary PI Unit Selection .................................................. 323
Secondary PI User Display .............................................. 323, 325
Second Line Monitor Selection ......................................... 186, 318
Selecting the Type of Auto-Tuning .......................................... 144
Selection of Parameter Write during Uv..................................... 319
Self-Diagnostics................................................................. 355
Sequence Timer 1 Day Selection ............................................. 321
Sequence Timer 1 Reference Source......................................... 321
Sequence Timer 1 Selection................................................... 321
Sequence Timer 1 Start Time ................................................. 321
Sequence Timer 1 Stop Time ................................................. 321
Sequence Timer 2 Day Selection ............................................. 322
Sequence Timer 2 Reference Source......................................... 322
Sequence Timer 2 Selection................................................... 322
Sequence Timer 2 Start Time ................................................. 322
Sequence Timer 2 Stop Time ................................................. 322
Index
390
YASKAWA ELECTRIC TOEP C710616 45E YASKAWA AC Drive – Z1000 User Manual