Yaskawa AC Drive Z1000 - Manual (Page 391)

Sequence Timer 3 Day Selection ............................................. 322
Sequence Timer 3 Reference Source......................................... 322
Sequence Timer 3 Selection................................................... 322
Sequence Timer 3 Start Time ................................................. 322
Sequence Timer 3 Stop Time ................................................. 322
Sequence Timer 4 Day Selection ............................................. 323
Sequence Timer 4 Reference Source......................................... 323
Sequence Timer 4 Selection................................................... 323
Sequence Timer 4 Start Time ................................................. 322
Sequence Timer 4 Stop Time ................................................. 323
Sequence Timer Error .......................................................... 228
SEr ................................................................................ 215
Serial Comms Cable Connection Terminal ................................. 340
Serial Communication Terminals...............................................92
Serial Communication Transmission Error ................................. 218
Set Time.............................................................. 114, 191, 320
Setup Group ..................................................................... 117
Setup Group Parameters ....................................................... 118
Setup Mode ...................................................................... 115
Shielded Twisted-Pair Cables ...................................................98
Simple Motor Setup Using V/f Control...................................... 121
Simplified Setup Using the Setup Group .................................... 115
Sinking/Sourcing Mode Switch for Digital Inputs ...........................91
SN...................................................................................91
Soft Charge Bypass Relay Maintenance..................................... 333
Soft Charge Bypass Relay Maintenance Time.............................. 221
Soft CLA Selection ............................................................. 314
Soft Starter Speed Reference at Previous Fault............................. 331
Software Current Limit Selection ............................................ 183
Software No. (Flash) ........................................................... 330
Software No. (ROM) ........................................................... 330
Software version ..................................................................27
Sound from Motor .............................................................. 241
Speed Agreement Detection Level ........................................... 312
Speed Agreement Detection Level (+/-)..................................... 312
Speed Agreement Detection Width .......................................... 312
Speed Agreement Detection Width (+/-) .................................... 312
Speed Control Range ........................................................... 272
Speed Feedback Detection Control Gain .................................... 317
Speed Response ................................................................. 272
Speed Search Deactivation Current .......................................... 159
Speed Search Deceleration Time ............................................. 159
Speed Search Delay Time ..................................................... 159
Speed Search Detection Compensation Gain ............................... 160
Speed Search Method Selection .............................................. 160
Speed Search Restart Current Level.......................................... 160
Speed Search Restart Detection Time........................................ 160
Speed Search Selection at Start ............................................... 159
Speed Search Wait Time....................................................... 160
Stall Prevention ................................................................. 200
Stall Prevention Level during Acceleration ................................. 311
Stall Prevention Level during Run ........................................... 311
Stall Prevention Limit during Acceleration ................................. 311
Stall Prevention Selection during Acceleration............................. 311
Stall Prevention Selection during Deceleration............................. 311
Stall Prevention Selection during Run ....................................... 311
Standard Connection Diagram ..................................................62
Standards......................................................................... 273
Starting Torque.................................................................. 272
Start-Up Flowcharts ............................................................ 119 Stationary Auto-Tuning........................................................ 144
Stationary Auto-Tuning for Line-to-Line Resistance ...................... 142
Status Display ................................................................... 123
STo ............................................................................... 215
STOP Key Function Selection ................................................ 188
Stopping Method after Communication Error ........................ 177, 342
Stopping Method Selection.................................................... 129
Storage Temperature .............................................................42
Supported Properties of Objects .............................................. 348
Surrounding Area .................................................................42
Swing PWM ..................................................................... 133
T
T/L3.................................................................................81
T1-03 ............................................................................. 145
T1-04 ............................................................................. 145
T1-05 ............................................................................. 145
T1-06 ............................................................................. 145
T1-07 ....................................................................... 145, 146
T1 Tuning Start ................................................................. 327
T2 Tuning Start ................................................................. 149
Task Complete .................................................................. 231
TdE ............................................................................... 215
Temperature Derating .......................................................... 277
Terminal A1 Bias Setting...................................................... 136
Terminal A1 Function Selection.............................................. 175
Terminal A1 Gain Setting ..................................................... 136
Terminal A1 Signal Level Selection ......................................... 174
Terminal A2 Bias Setting...................................................... 137
Terminal A2 Function Selection.............................................. 175
Terminal A2 Gain Setting ..................................................... 137
Terminal A2 Signal Level Selection ......................................... 175
Terminal Block Configuration ..................................................68
Terminal Board .............................................................. 34, 35
Terminal Board Connection Error............................................ 206
Terminal Connections for Communication Self-Diagnostics............. 355
Terminal Cover ............................................ 32, 33, 34, 35, 36, 70
Terminal TB1 .....................................................................37
Terminal TB2 .....................................................................37
Terminal TB3 .....................................................................37
Terminal TB4 .....................................................................37
Terminal TB5 .....................................................................37
Test Run.................................................................... 143, 146
Test Run Checklist.............................................................. 154
Test Run with Load Connected ............................................... 151
Third Line Monitor Selection ........................................... 186, 318
Tightening Torque ................................................................83
TIM ............................................................................... 215
Time Data Error................................................................. 215
Time Not Set .................................................................... 215
Time to Continue Making Fault Restarts .................................... 312
Too Many Speed Search Restarts............................................. 215
Torque Compensation Gain ................................................... 198
Torque Compensation Primary Delay Time ................................ 198
Torque Detection Level 1................................................ 141, 313
Torque Detection Selection 1 ........................................... 140, 313
Torque Detection Time 1 ................................................ 141, 313
Torque Specifications, Three Phase 200 V Class ............................83
Torque Specifications, Three Phase 400 V Class ............................85
Troubleshooting without Fault Display...................................... 235
Index
YASKAWA ELECTRIC TOEP C710616 45E YASKAWA AC Drive – Z1000 User Manual 391