Lenze EVS9332xK - Manual (Page 460)

Appendix
Index
13
13.3
l
13.3−2 EDSVS9332K EN 8.0−07/2013
Control terminals, 5.8−1
− Changing the assignment of X5, 6.9−1
− Changing the assignment of X6, 6.9−1
Controller
− Adaptation to mains, 6.5−2
− Application as directed, 1.2−1
− Identification, 1.2−1
Controller inhibit
− Drive behaviour, 6.4−1
− Terminal assignment, 5.8−9
Current characteristics, current derating, 3.4−1
Current controller adjustment, 6.7−1
Current derating, 3.4−1
Current load of controller, Ixt monitoring, 8.2−5
Current load of the motor, I2 x t monitoring, 2.2−1, 8.2−7
D
Data model
− Absolute, 6.10−2
− Definition, 6.10−2
− Relative, 6.10−2
DC supply, 5.3−1, 5.4−4, 5.5−4, 5.6−4, 5.7−4
DC−bus connection
− Central supply, 10.5−1
− Distributed supply, 10.4−1
DC−bus operation, 10−1
− Conditions, 10.2−1
− Several drives, 10−1
DC−bus voltage, 8.2−9, 8.4−4
− Monitoring, 8.2−9
− Overvoltage, 8.2−9
− Undervoltage, 8.2−9
Deceleration time, 8.4−3, 8.4−13
Definition of notes used, 1.4−1
Definitions, Terms, 13.2−1
Device control, 8.4−2
Device protection, 2.3−2
Diagnostics, 7.2−10, 9.1−1
Digital frequency input, connection to X9, 5.11−1
Digital frequency output, connection to X10, 5.11−1
Digital input signals, 6.9−1
Digital inputs, Terminal assignment, 5.8−9
Digital inputs/outputs, Terminal assignment, 11.4−1
Digital output signals, 6.9−2
Digital outputs
− Configuration, 6.9−2
− Terminal assignment, 5.8−9
Dimensions, 3.1−2, 4.1−3, 4.1−5, 4.2−3, 4.2−5, 4.3−3,
4.4−3
Discharge current, Mobile systems, 5.2−4
Display, operating status, 9.2−1
Display functions, 9.1−1
Disposal, 2.1−3
Distributed supply, 10.4−1
Drive behaviour
− Controller inhibit, 6.4−1
− Influence of the motor cable length, 5.2−8
E
E.l.c.b., 5.2−3
− operation at, 5.2−3
Earth fault in motor cable (OC2), 8.2−4
Earth−leakage circuit breaker, 5.2−3
− operation at, 5.2−3
Electrical installation, system bus (CAN), 5.9−1
EMC, what to do in case of interferences, 5.3−6
Emergency−off, Controller inhibit, 6.4−1
EMZ9371BC keypad, changing parameters, 7.2−7, 7.2−8
EN 61000−3−2, 3.1−2, 5.2−1
− operation on public supply systems, 5.2−1
Entry of feed constants, 6.5−3
Entry of gearbox factors, 6.5−3
Entry of motor data, 6.5−5
Error analysis
− Via history buffer, 9.2−2
− via LECOM status word, 9.2−3
Error messages, 9.3−1
− causes and remedies, 9.3−1
− configuration, 8.31
− General, 9.3−1
− Resetting, 9.3−6
Exceeding of the maximum speed (NMAX), 8.2−4
Explanations, Code table, 8.4−1
External error (EEr), 8.2−9
F
FAIL−QSP, 8.2−1
Failure of a motor phase, 8.2−4