Rockwell Automation 8520-MUM 9/Series CNC Mill Operation and Programming Manual Documentation Set - Manual (Page 949)

9/Series PAL Reference Manual
Index (General)
9/Series Mill
Index
Operation and Programming Manual
xvii
Tool Data, Assigning Detailed, 20-25
Tool Directory Data, 20-20
Tool Gauging Function (G37), 27-1
Tool Length Axis Selection, 20-9
Tool Length Offset Function (G43, G44, G49), 20-3
Tool Management, 20-19
Tool Offset Dimensional Parameters, 3-2
Tool Offset Table Setup, 3-1
Tool Offset Words, 10-22
Tool Offsets
Activating, 20-8
backing up, 3-17
changing active, 3-12
entering diameter values, 3-4
entering diameter wear values, 3-5
entering length values, 3-2
entering length wear values, 3-4
entering using G10, 3-5
entering using measure, 3-5
entering using paramacros, 3-5
entering using skip cycle, 3-5
entering using though PAL, 3-5
Length, 20-3
manually entering data, 3-5
offset numbers, 3-2
on shared axis, 30-30
range verification, 3-10
Tool Path, Displaying, 8-24
Tool Position, as offset, 11-13
Tool Selection, 10-40
Torque, feedrate control (G25), 18-9
Trailing Zero Suppression (TZS), 10-18
Transfer Line Cycles
creating, 31-9
customizing, 31-5
Description, 31-3
editing, 31-12
Example, 31-4
M--Codes, 31-16
Paramacro Variables, 31-14
reloading templates, 31-17
replacing, 31-17
Running, 31-25
selecting, 31-6
using G17/G18/G19, 31-25
using G90/G91, 31-25
using G98/G99, 31-25
using spindles, 31-25
Transfer line cycles
Back Boring Cycle, 31-2, 31-15, 31-43
Boring Cycle, Dwell/Feed Out, 31-2, 31-15, 31-44
Boring Cycle, No Dwell/Feed Out, 31-2, 31-15, 31-38
Boring Cycle, Spindle Shift, 31-2, 31-15, 31-41
Boring Cycle, Spindle Stop/Rapid Out, 31-2, 31-15, 31-39
Deep Hole Drill Cycle, Chip Break, 31-2, 31-15, 31-32
Deep Hole Drill Cycle, Chip Clear, 31-2, 31-15, 31-30
Drilling Cycle, Dwell/Rapid Out, 31-2, 31-15, 31-28
Drilling Cycle, No Dwell/Rapid Out, 31-2, 31-15, 31-26
Left Hand Solid Tapping Cycle, 31-2, 31-15, 31-37
Left Hand Tapping Cycle, 31-2, 31-15, 31-36
Right Hand Solid Tapping Cycle, 31-2, 31-15, 31-35
Right Hand Tapping Cycle, 31-2, 31-15, 31-34
Single Axis Cross Cycle, 31-2, 31-15, 31-48
Single Axis Feed Cycle, 31-2, 31-15, 31-50
Single Axis Lift Cycle, 31-2, 31-15, 31-45
Single Axis Transfer Cycle, 31-2, 31-15, 31-46
Two Axis Cross Feed Cycle, 31-2, 31-15, 31-51
Two Axis Transfer Bar Cycle, 31-2, 31-15, 31-47
Transfer Line Templates
mutually exclusive features, 31-25
Optional Fields, 31-25
Required Fields, 31-25
Transmit Key, 2-3
Transpose, mirror, 14-36
Travel Limit, hard stop (G24), 14-40
Travel Limits, Resetting, 12-13
Trigonometric Functions, 2-6
TRVRS, 2-14
twin axes, 30-31
TZS, Using, 10-18
U
Uniform Acc/Dec, 18-16
Uploading Part Programs to ODS, 6-12
Using Interference Checking, 30-12
V
Values, Interpretation of Zeros, 10-18
Varying axis feedrate, torque mode (G25), 18-9
Verifying Programs, against source, 9-17
W
Wear Offset Table, 3-2, 3-6
Word Descriptions, 10-22